Installation Manual for Curt Double Lock Gooseneck Hitch C60734

Question

Question:

I just received my hitch, but it does not have instructions with it. Where can I get them?

asked by: Dale

0

Expert Reply:

I am sorry the install manual wasn't included with your Curt Double Lock Gooseneck Hitch # C60734. I have attached the PDF copies of the manual below (there are two sets) that you can save or print off when needed. Please just let us know if you have any other questions along the way!

expert reply by: Chris R

0

Toby

3/1/2025

When should I cut the hole for the ball when installing the C607034 hitch

Answer 1

On the Curt Double Lock, Flip and Store Underbed Gooseneck Hitch like part #C60720, there is a 3/8" guide pin in the lower portion of the receiver tube opening. This guide pin is designed to hold the hitch ball in place when the handle is pulled…

view full answer...

Answer 2

I checked with B and W and the correct replacement ball release latch pin handle you are looking for is the part #BW1900-2-2007 that you referenced for your B and W Turnoverball hitch #BWGNRK1111.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

Hey Jeff. There is definitely a correlation between weight and capacity. I've listed the weight of all three of the Power Mountain Tallboy Off-Road Bottle Jacks we have below: Power Mountain Tallboy Off-Road Bottle Jack - 7-15/16" to…

view full answer...

Answer 11

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 12

Hey Ian, great to hear from you again! The differences between the MORryde CRE3000 #MR87ZR and AllTrek 4000 #MR89DR that fit a 33" wheelbase is the height between the hanger and equalizer bolts, and the amount of travel the suspension style will…

view full answer...

Installation Manual for Curt Double Lock Gooseneck Hitch C60734

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching