Does BlayLock Coupler Lock # BLTL-22 Fit 2003 Ram Collar Lock Style Coupler

Question

Question:

My trailer has a Ram Sleeve 2inch coupler which is similar to the Bulldog but shaped a little different. Will the BLTL-22 fit? My coupler looks like one that etrailer sells, part # CA-5196-B.

asked by: Mike

0

Expert Reply:

Yes, the BlayLock Coupler Lock part # BLTL-22 does fit your Ram coupler jack that is a collar lock style like the # CA-5196-B. Your Ram coupler and the # CA-5196-B are the same as they are both made by same company.

expert reply by: Jameson C

0

Answer 1

I have a solution for you, the Blaylock Total-Encasement Coupler Lock for 2" Bulldog Collar-Lok Couplers - Push Button #BLTL-22 is designed to put on your trailer while it is not coupled to your tow vehicle. We can however use the trailer…

view full answer...

Answer 2

A pin with a 1/4 inch diameter, like part #e98886, is standard for coupler locks. Unfortunately there are none that are 1/16 of an inch larger in diameter. If instead you meant that you needed one with a span of 5/8 of an inch then you will want to…

view full answer...

Answer 3

An oil seal like Redline part #9103309 installs in the back side of the hub (the side nearest the trailer's frame) with the sides or "legs" of the seal inserted into the hub's bore. This means that the flat metal surface of the seal…

view full answer...

Answer 4

The first set of bearings are Timken which we don't carry and don't have a cross reference for. We do have the race #L44610, with what I believe you meant to type #L44649, race #L68111, and bearing #L68149 with seal #RG06-050.

view full answer...

Answer 5

The #BK2-100 Bearing Kit for #84 Spindle L44649/L68149 Bearings 10-19 Double Lip Seal will work. You have EZ Lube spindles which do not use a cotter pin. The spindle has a tube in it for the grease to be pumped in. Instead it uses a tang washer,…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

Thank you for providing the specs for the suspension components that you already have. Correct hanger spacing really depends on the components being used such as springs, hangers and equalizers. Most of the hanger spacing dimensions that we have are…

view full answer...

Answer 10

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Does BlayLock Coupler Lock # BLTL-22 Fit 2003 Ram Collar Lock Style Coupler

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching