Replacement for Dexter 12-1/4 Inch x 5 Inch Electric Brake Magnet K71-377-00

Question

Question:

Will this replace dexter brake magnet part K71-377-00?

asked by: Matt

0

Expert Reply:

Yes, the Replacement Magnet for Dexter 12-1/4" x 5" Electric Brake Assemblies part # BP01-306 actually replaced the Replacement Magnet for Dexter 12-1/4" x 5" Electric Brake Assemblies part K71-377-00 so they will work well in place of one another.

expert reply by: Conner L

0

Answer 1

It sure does Brian. The Lippert Hub and Drum Assembly item #LC57DX will indeed work with a threaded grease cap. It has a hub bore of 2.722". This hub is designed for 8,000 lbs axles and has a 8 on 6-1/2 lug pattern. It fits spindles with a inner…

view full answer...

Answer 2

I have a solution for you, but there is not an exact size replacement available for your Atwood GCH6A-10E water heater, which looks like was 16" wide x 12-1/2" tall x 20" deep. With that said, the closest match is theDometic RV Water…

view full answer...

Answer 3

You are close. The Replacement Magnet for Dexter 12-1/4" x 5" Electric Brake Assemblies #BP01-306 you were looking at are for brake assemblies that are 12-1/4" in diameter, and 5" deep measure on the inside of the drum. You can…

view full answer...

Answer 4

Thanks for the picture of your AC unit. Based on that for a white replacement you would need the part #DMC46FR.

view full answer...

Answer 5

Hey Eric! Yes, the Cummins Onan Quiet Series Onboard RV Generator - 4,000 Watts - Gasoline #CM32ZR is the correct replacement for the generator in your motorhome. This will fit in the same spot as your existing QG 4000. What happened to your old…

view full answer...

Answer 6

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 7

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 8

Hey Fraser, yes the Dometic thermostat part #DMC83ZR that you referenced is correct for you to use when adding the Dometic Freshjet 3 part #DMC49ZR. This thermostat had furnace controls as well.

view full answer...

Answer 9

The "Trailer Disconnected" error message on the dash with a factory brake controller is usually related to an issue with the blue brake output wire that runs from the brake controller to the 7-Way connector. The fact that the issue remains…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Replacement for Dexter 12-1/4 Inch x 5 Inch Electric Brake Magnet K71-377-00

Product Page this Question was Asked From

Continue Researching