Dimensions of Replacement Pocket Nut for TracRac SR Sliding Ladder Rack Base Rails

Question

Question:

What are the dimensions for the Replacement Pocket Nut for TracRac SR Sliding Ladder Rack Base Rails TA01-2100N?

asked by: Donald E

0

Expert Reply:

The Replacement Pocket Nut for TracRac SR Sliding Ladder Rack Base Rails part # TA01-2100N measures 1-3/4" long x 1" wide x 1/4" thick.

expert reply by: Conner L

0

Answer 1

You will need the Replacement Rubber Block for Base Rail Installation of TracRac Sliding Ladder Racks - Qty 1 #TARB-11032-1. You can get the pocket nut separately #TA01-2100N, but the bolts and other hardware are only available in the Replacement…

view full answer...

Answer 2

The Tonneau cover that is in the customer's pictures (see attached) is the BAKFlip F1 Hard Tonneau Cover #BAK72122. However in that same review, the customer says that the cover and the rack rub against each other. That rubbing will likely cause…

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 5

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 6

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 7

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 8

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 9

Hi Clint, welcome back The HappiJac Original Turnbuckles for Camper Tie-Downs - Stainless Steel - Qty 4 #LC182898 are likely what you are looking for and will be a good in between option (they are actually pretty nice and should last a good long…

view full answer...

Answer 10

Hey Rod, thanks for reaching out. Yes, it will! The Curt Helux Shock-Absorbing 5th Wheel Pin Box #C83RJ will indeed work with the Demco Autoslide 5th Wheel Hitch #DM8550038. Just make sure you also use the Demco Autoslide Locking Plate for Lippert…

view full answer...

Answer 11

Hello Dennis, That is definitely something you will want to check with your setup. The B&W Continuum #BW78FR will sit about 9 inches below your trailer frame once installed, so you will want to measure from the ground to the bottom of the frame…

view full answer...

Answer 12

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Dimensions of Replacement Pocket Nut for TracRac SR Sliding Ladder Rack Base Rails

Product Page this Question was Asked From

Continue Researching