How To Measure For A Truck Bed Camper Cover For Storage

Question

Question:

Yes I am trying to figure out which length I use to a cover for my 2011 Palomino 1000. Floor length, or overall length? A cover recommendation would be nice as the Michigan winter is fast approaching.

asked by: Jacob

0

Expert Reply:

I am happy to help you figure out the cover that you need for the 2011 Palomino 1000 to withstand the harsh Michigan winter. I believe the Palomino 100 is a truck bed camper. I have attached a diagram that shows where to measure to get the correct fit. If you can let me know these measurements I can assist you further.

expert reply by: Heather A

0

click to enlarge

Answer 1

For your 2022 Lance 850 truck camper that measures 18 feet in length the best option for a cover is the Camco Ultraguard part #CAM45770 which provides the best protection in hot and dusty climates and also is easier to fit and install.

view full answer...

Answer 2

From what I could find it looks like a Lance 975 slide-in camper is 19-1/2' long so the Camco UltraGuard #CAM45770 for 18' campers isn't quite long enough. The Camco UltraGuard #CAM45773 is designed or 19-1/2' campers but you'll…

view full answer...

Answer 3

Hey Tobin! The Camco item #CAM45771 is going to be a bit short for your 2024 Palomino 750 but I have an identical one that will work. It is the Camco UltraGuard Slide-In Camper Cover item #CAM45773. This ones 18' long and has the same features.…

view full answer...

Answer 4

The Adco SFS AquaShed RV Cover for Truck Campers up to 10' Long #290-12264 has weighted straps that buckle underneath your camper to secure it to the body. The excess material can be tightened up with the cinch ropes at the front and rear of the…

view full answer...

Answer 5

The best option for your 17 foot 10 inch truck camper is the Camco UltraGuard Slide-In Camper Cover #CAM45770 which is designed to fit campers that are up to 18 feet. This cover is made to protect campers that are in wet climates like yours; it has a…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

We have lift kits for trailer that easily add 2 inches to the height of the trailer. For that you'd want the part #RR23QX and you'd be set. I attached a picture that shows how it installs to give you an idea. This would be the easiest…

view full answer...

Answer 11

Hello Joe, Thank you for reaching out! The Power Mountain Tallboy Off-Road Bottle Jack - 11-5/16" to 27-1/16" Lift - 12 Tons #PM94FR does have the capacity you’d need, but since your fifth wheel’s frame sits about 25" off the ground,…

view full answer...

Answer 12

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

How To Measure For A Truck Bed Camper Cover For Storage

Product Page this Question was Asked From

Continue Researching