Converting Stallion Landing Gear Jack on Trailer to a Powered Jack

Question

Question:

We would like to add an electric jack to our 4 horse Silverado gooseneck It currently has a stallion model 52000 spring loaded leg jack single jack What would be the best electric jack for this situation Thanks

asked by: [email protected]

0

Expert Reply:

The best option to convert your single landing gear jack setup to a powered jack would be with the Bulldog landing gear jack # BD183902 and the powered drive kit # BD1824180100. This will give you a single jack setup that will attach to your trailer in place of your current Stallion jack and a powered drive kit that would allow you to raise and lower your jack without requiring you to crank it up and down.

expert reply by: Jameson C

0

Answer 1

Yes, 7k trailer axle brake assemblies like #23-180-181 will fit 6k axle hub/drums. They use the exact same dimensions and bolt patterns which allows that. The difference is the strength or sensitivity of the magnets in the assemblies. The 7k axles…

view full answer...

Answer 2

The difference between the Dexter Electric Trailer Brake Kit - 12" - Left and Right Hand Assemblies - 7,000 lbs #23-180-181 and the #23-105-106 you mentioned are the strength of the brake magnets. The #23-180-181 was designed for 7000lb axles…

view full answer...

Answer 3

I may have a different solution for you, but there will not be a universal kit to add a motor to your Stallion jack, unfortunately. With that being said, I have 2 options below for you to check out. Both will be weld on applications, but are…

view full answer...

Answer 4

The Stallion Jack brand is not directly compatible with anything we carry. The closest thing we have is the Replacement Rod and Nut for etrailer and Ram Square, Direct Weld Jacks - 12K #TJD-12000-RODNUT which is 3-1/2 inches x 3-1/2 inches. I…

view full answer...

Answer 5

We do have a large selection of trailer jacks that should work nicely on your gooseneck trailer, however I was unable to find any information on your existing Stallion jack using the patent number that you provided. For a replacement jack, I…

view full answer...

Answer 6

The Replacement Return Spring for etrailer and Ram Square, Direct Weld Jacks part #TJD-12000-RSP is 12-1/4" long x 3/4" diameter overall.

view full answer...

Answer 7

To determine the location for the front and rear hangers on your tandem axle trailer you will first need to make sure that you have the correct center point for your equalizer hanger. The center point of your equalizer hanger needs to be located…

view full answer...

Answer 8

I understand how it would be unclear which measurement to use since the center of the axle is not the same as the center of the wheel on a torsion axle. For a single axle trailer, measure from the center of the spindle (center of wheel) to the…

view full answer...

Answer 9

I do have an alternative option for you but I spoke to my contact at Edge Products and they informed me that they do not make an extension cable to extend the video cable from the rear of your travel trailer to the cab where your Edge monitor is…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Converting Stallion Landing Gear Jack on Trailer to a Powered Jack

Continue Researching