How To Measure For Replacement Door Latch
Updated 10/01/2019 | Published 09/30/2019 >
Question:
Good Day, have an old service body off of a ATandT truck and need to replace all the latches.. Have not been able to locate any replacements. The dimensions are 5 1/4 x 6 1/2. Do you have anything available in either locking or non-locking?
asked by: Brian
Expert Reply:
The measure that is really important when choosing latches is the cut out measurement. If the cut outs on your truck are 5-1/4" x 6-1/2" for the latch then we do not carry a fit because Paddle Handle Locking Latch w/ Release part # PLR5115 is the latch with the largest cut out available at 4-5/8" long x 3-3/8". If you take off one of the latches and measure the cut out then you can compare that measurement with the latches we have available which I have attached below. Most of our parts are for enclosed trailers so the truck may use larger latches then the common trailer sizes.
Product Page this Question was Asked From
Locking Paddle Handle w/ Internal Release - 5-1/2" Long x 4-1/4" Tall - Zinc Plated Steel
- Trailer Door Latch
- Reversible
- Flush Latch
- Keyed Unique
- Built In Lock
- Metal
- Polar Hardware
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector
- Search Results: horse trailer hinge
- Shop: Cam-Action Lockable Door Latch w/ 36" Pipe for Enclosed Trailers - Zinc Plated Steel
- Shop: Demco Hydraulic Brake Actuator - Drum - Zinc - 2" Ball - 7,000 lbs
- Shop: Easy Grease Trailer Idler Hub Assembly for 3.5K Axles - 5 on 4-1/2 - Galvanized
- Shop: Easy Grease Trailer Hub/Drum Assembly for 3.5K Axles - 10" Diameter - 5 on 4-1/2 - Galvanized
- Shop: Square Corner T-Strap Hinge w/ Reverse Bracket - 270 Degree - 12-1/8" Long - Zinc Plated
- Shop: Tamper-Proof Door Latch w/ 36" Pipe for Enclosed Trailers - Zinc Plated Steel
- Search Results: clearance light
- Search Results: clearance
- Search Results: grease cap
- Search Results: square tail light
- Search Results: bearing dust cap
- Search Results: grab handle
- Shop: Trailer Hitch
- Q&A: Recommended Flush Door Latch for Wells Cargo Trailer
- Q&A: How to Measure the Angle of Trailer A Frame To Determine if a 50 Degree A Frame Coupler will Fit
- Q&A: Recommended Replacement Entry Door Latch for a 1995 Jayco 1207 Pop Up
- Q&A: Can Polar Handle PLR5115 Replace Bargman 10-60-011
- Q&A: What Is The Angle For The etrailer A-Frame Trailer Coupler?
- Q&A: How to Mount Junior Door Latch # L1930
- Q&A: Does Locking Stainless Steel Flush Door Latch Come With Gasket Or Strike Plate
- Article: 4 Steps to Choosing Your 5th Wheel Pin Box
- Article: Trailer Lighting Requirements
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Article: 2 Steps for Finding the Right Weight Distribution Hitch Size
- Article: Trailer Wiring Diagrams
- Article: Parts Needed to Add Electric Drum Brakes to a Trailer
- Article: How to Install E-Track in 3 Easy Steps

