Can Anti-Rattle Trailer Hitch Receiver Lock # 63232 be Used When Towing

Question

Question:

Can i use it in hitch when towing my travel trailer?

asked by: Dick Y

0

Expert Reply:

Yes, the Anti-Rattle Trailer Hitch Receiver Lock # 63232 can be used on a ball mount that is being used to tow a travel trailer as long as the shank of the ball mount is hollow. It will make the towing setup a bit quieter and also locks the ball mount to the tow vehicle as well.

I attached a review video for this for you to check out as well.

expert reply by: Jameson C

0

Answer 1

A trailer with a 5000 lb GTW (gross trailer weight) could potentially have a tongue weight 10-15% of its GTW which would be 500-750 lbs. The Curt TruTrack #C17499 Weight Distribution system can handle tongue weights ranging from 500-800 lbs, so…

view full answer...

Answer 2

The rattle or play you experienced is very common and the solution isn't to replace the ball mount with a tighter fitting one as that's not really possible but is to use an anti-rattle device like the part #63232. This installs in the shank…

view full answer...

Answer 3

When it comes to choosing between the Curt TruTrack Weight Distribution System w/ Sway Control #C17499 and the Equal-i-zer Weight Distribution System w/ 4-Point Sway Control #EQ37100ET you'll want to take a couple of things into consideration: 1.…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

Hi Mike; we don't have a way to swap out the 2" ball on the Andersen Weight Distribution Hitch #AN88VR. We do have the 2-5/16" ball separately, #AN45VR, but we don't have it as a complete system. If you really want the Andersen,…

view full answer...

Answer 10

Not another one! Just kidding Dirk! I was in the Marines I enjoy these conversion questions on the M1101 trailers. I'd be more than happy to list the parts you need, along with quantity, and confirm compatibility. 1 - Timbren Axle-Less Trailer…

view full answer...

Answer 11

-Hey Tom, Equal-i-zer makes frame brackets for 8 inch trailer frames. For that you would need the part #EQ90-02-5378 for outer link and then for an inner link part #EQ90-02-5208. You'd need two of these with the system you order since the…

view full answer...

Can Anti-Rattle Trailer Hitch Receiver Lock # 63232 be Used When Towing

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching