Dimensions of Ventline RV Range Hood Replacement Switch BL0108-02

Question

Question:

Could provide the length and width of the switch? Thank you.

asked by: Gina

0

Expert Reply:

The Replacement Fan Switch for Ventline RV Range Hoods is 0.85" long x 0.594" wide x 0.9" deep (from bottom of bezel to the terminals). This replacement switch is designed to fit on Ventline S0721 Series range hoods. If you have a different range or size switch, please let me know and I can help you find a different replacement.

expert reply by: Erik B

0

Answer 1

Hey David, thanks for reaching out and providing all of the information! I'm not seeing that we're able to separate out the pieces like you're wanting, but we do have the entire roof vent lid assembly as part #DMC59MR on our site (which…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 4

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 5

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

The two sizes you mentioned are pretty similar and fit many of the same 15 inch wheels. The 205/75-15 fits rim widths of 5 inch to 6 inch whereas the 225/75-15 fits widths that are 5 inch to 6-1/2 inch. The 205 is 27.1 inches tall and the 225 is 28.4…

view full answer...

Answer 9

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 10

Kevin, I think you are absolutely making the right call replacing those tires. Even though they still look great on the outside, eight year old trailer tires are getting into the age range where internal deterioration becomes a bigger concern than…

view full answer...

Answer 11

Hey Bill thanks for the information. The C865H-9/16 in that axle tag number means you have 8 on 6-1/2 hubs with 9/16" lug studs. The Hydrastar item #HSE7K-T1, you were looking comes with 1/2" lug studs. You'll need the Hydrastar Disc…

view full answer...

Answer 12

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Dimensions of Ventline RV Range Hood Replacement Switch BL0108-02

Product Page this Question was Asked From

Continue Researching