Why Blinkers Stop Flashing When Brakes Are Applied On 2005 Ram 3500
Updated 05/09/2024 | Published 08/20/2019 >
Question:
I recently installed a flatbed on my 04 Ram 3500. I replaced all bed lights with LEDs. I installed load resistors on each circuit left side running, left side stop/turn signal, right side running, right side stop/turn signal, reverse lights, license plate lights. All lights work as they should except when the blinkers are on and I apply the brakes, the blinkers stop flashing. Any ideas?
asked by: Jason D
Expert Reply:
Ram trucks made in years including your model have separate brake light and blinker circuits that can't be combined without a converter. What you need is a signal converter to combine the turn signal and stop signal so they can work together on the same bulb.
Three wire systems use a separate wire to carry the brake signal. Two wire systems have the brake and turn signals sent along the same wire. Using a converter like # RM-732 takes separate brake and turn signals and combines them so that the brake and turn signals are on the same circuit.
Wire your separate turn signals to the input side of the box and then on the output side the signals will match what your truck needs.
Product Page this Question was Asked From
Roadmaster Brite-Lite 3-to-2 Tail Light Converter for Towed Vehicles
- Flat Tow Wiring Harness
- Splices into Vehicle Wiring
- Tail Light Converter
- Universal Fit
- Roadmaster
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Shop: Vehicle Tow Bar Wiring
- Shop: Roadmaster Brite-Lite 3-to-2 Tail Light Converter for Towed Vehicles
- Shop: Roadmaster Tail Light Wiring for Towed Vehicles w/ 7-Wire to 6-Wire Straight Cord Kit
- Shop: Curt Universal Tail Light Wiring Kit for Towed Vehicles - 4-Way Flat Connectors
- Shop: Roadmaster Smart Diodes for Variable Voltage LED Tail Lights - Qty 2
- Shop: Blue Ox Block Diode Tail Light Wiring Kit for Towed Vehicles
- Shop: Roadmaster 4-Diode Universal Wiring Kit for Towed Vehicles - 4-Way Flat Connectors
- Shop: Curt 2-to-3 Tail Light Converter for Towed Vehicles w/ Incandescent Tail Lights
- Article: Brake Controller Installation: Starting from Scratch
- Q&A: How Do You Know if the Stop Light Switch Kit is Needed When Installing SMI Air Force One
- Q&A: How to Make an Adapter to Go from Semi Truck 7-Way Round to RV Style 7-Way Blade on Trailer
- Video: Curt 2 to 3 Wire Tail Light Converter: The Breakdown
- Video: Complete Breakdown of the Roadmaster Brite-Lite Wiring Converter
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Video: An In-Depth Look at the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
- Q&A: Recommended Bike Rack and Dual Hitch Adapter for Carrying E-Bikes While Flat Towing
- Search Results: trailer hitch
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer wiring
- Q&A: How to Replace a Lance 6-Pin Plug w/ a Standard 7-Way Connector
- Shop: Trailer Wiring
- Video: An In-Depth Look at the Roadmaster Battery Charge Line Kit for Towed Vehicles
- Shop: Suspension Enhancement
- Search Results: base plate for tow bar
- Article: How to Measure for Trailer Hitch Drop
- Q&A: Which is Better Roadmaster or Blue Ox Tow Bar
- Video: Breaking Down the Roadmaster Diode 7-Wire to 6-Wire Flexo-Coil Wiring Kit
- Shop: Base Plate for Tow Bar
- Search Results: trailer lights



Bryan P.
5/9/2024
I tried this converter for my 2005 Dodge 3500 flatbed and the blinkers work fine but the brake lights don’t come on when applied. What do you think is wrong?