How To Determine Which Replacement Brake Assemblies I Need For A 1999 Coleman Fleetwood Westlake

Question

Question:

What electric brakes do I need for Dexter Axle P-11 SLR, SND 257953. Replacements on a 1999 Coleman Fleetwood Westlake.

asked by: Richard

1

Helpful Expert Reply:

To determine which electric brake assemblies to use on your 1999 Coleman Fleetwood Westlake, you will want to measure the inside diameter of the brake/drum and the depth of your hub. You also would want to know the axle capacity and wheel size to ensure compatibility. I was not able to find the axle rating from the information you provided. I have attached a photo for your reference.

For example the etrailer.com Electric Trailer Brake Kit part # AKEBRK-35-SA are 10" assemblies that measure 2-1/4" wide. They are compatible with wheel sizes 13", 14", and 15" and the standard axle rating of 3,500 lbs. If you let me know this information, I can recommend braking assemblies for the Coleman Fleetwood.

expert reply by: Heather A

1

click to enlarge

Answer 1

The 8 inch diameter wheel on your Coleman Fleetwood pop-up camper is not large enough to accept an electric brake hub and drum assembly. Seven inch brake assemblies like #23-48 that you selected work with the Trailer Hub & Drum Assembly, item…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 4

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Hi Calvin! All of the pre-greased hubs/drums, like the Terran Industries Trailer Hub and Drum Assembly - 3.5K Axles - 10" Diameter - 5 on 4-1/2 #TX68VJ, come with bearings made overseas and are all basically the same quality. At least that I…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 11

I currently have four different self-adjusting assemblies for your boat trailer with 10" x 2-1/4" electric drum brakes. You can choose from the following: -Terran Axle Electric Trailer Brakes #TX97ZJ (3,500 Axles) -etrailer Electric Trailer…

view full answer...

Answer 12

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

How To Determine Which Replacement Brake Assemblies I Need For A 1999 Coleman Fleetwood Westlake

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching