Are Rubber Insides for Road Armor Shock Absorbing Equalizer Kit Replaceable

Question

Question:

Is the rubber bushings in the Road Armor Equalizer set up replaceable? With only a 1 year warranty, I want to know if they have a rebuild kit and what do they cost? It appears after removing the equalizer from the trailer, 3 bolts would take it apart, so a repair looks to be fairly strait forward. Please let me know.

asked by: David F

0

Expert Reply:

I reached out to my contact at Lippert and he said that the rubber inside part of the Road Armor Shock Absorbing Equalizer Kit # LC696740 is not replaceable so if it were to become damaged you would need to replace the unit.

expert reply by: Jon G

0

Richard M.

6/2/2025

The bottom rubber is protruding out about an inch , is it still safe to travel, Or can it be put back in?

Jon G.

6/3/2025

@RichardM If the rubber parts of your Road Armor are starting to stick out more than normal then I'd look into replacing them - you wouldn't want to be driving down the road and have something happen with your suspension.

Richard M.

6/3/2025

@JonG Thanks Jon I am traveling at the moment so I can replace them when I get home, but that’s gonna be in another month. I was looking at the design of it and there is a bolt that goes through the middle that holds the what I call the pivot rod, so I’m assuming that if the rubber does come out that it will still be OK it just won’t have the shock absorbing on the bottom part. What do you think?

Jon G.

6/3/2025

@RichardM It will all still hold together, yes, it will just give your trailer more of a jarring ride.

Answer 1

The angled portion of the flanges on the part #115983 should run front to back on your trailer and should angle away from your leaf spring. See the attached picture to see exactly how they should install. Typically there are bushings installed in the…

view full answer...

Answer 2

Hello Jerry, thanks for reaching out. I am sorry to say we do not offer a replacement rod and nut for the Lippert Ground Control 3.0 jacks. The only solution I can offer would be a whole new leg such as part #LC362485 which replaced the front jack…

view full answer...

Answer 3

I reached out to Kodiak and found that the rotor thickness on the Kodiak Disc Brake Kit - 13" Hub/Rotor - 8 on 6-1/2 - Raw Finish - 7,000 lbs #K2HR712 is 25.66 mm.

view full answer...

Answer 4

The quickest way we can help you determine your Dexter axle capacity is going to be to measure the diameter of it. I can email them your serial number and they'll get back to me hopefully quickly but if measure your diameter you'll know…

view full answer...

Answer 5

There is a wet bolt kit made specifically for a tandem axle trailer with Road Armor equalizers, and includes the shackles, wet bolts, and hardware needed. What you need is the following part: - Lippert AP Kit - Tandem Axle Road Armor Wet Bolts and…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 12

Hello Sam; that is a great question! I reached out to Furrion and you will be able to use the Furrion Chill Cube #FR69TD (white) or #FR49TD (black) with your furnace. However, the remote is not capable of operating the furnace at this time. Also, we…

view full answer...

Are Rubber Insides for Road Armor Shock Absorbing Equalizer Kit Replaceable

Featured Help Information

Miscellaneous Media

Continue Researching