Size Wrench Used to Install Brophy Hitch Ball # SC23-C

Question

Question:

Hi, what wrench sizes will i need to install this ball pin?

asked by: J D

0

Expert Reply:

Brophy recommends using two large crescent wrenches to install the # SC23-C. Or at least one crescent wrench on top of the ball and a 1-7/8 inch wrench on the bottom.

expert reply by: Jameson C

0

Answer 1

Yes, you can absolutely use an aluminum ball mount with a stainless steel hitch ball without worry of the ball mount corroding. In fact, there are no aluminum hitch balls so manufacturers suggest the use of stainless steel as it is going to be the…

view full answer...

Answer 2

I went to the warehouse and measured the Brophy 2-Inch Hitch Ball, part #SC23-C. The length of the shank from the underside of the platform that sits on the ball mount is 2-1/2 inches. The threaded portion of the shank measures 2-1/8 inch. I have…

view full answer...

Answer 3

To install the Brophy 2-Inch Hitch Ball #SC23-C on Fulton Ball Mount #F47CR you will use a suitable torque wrench (one like #ALL944001) to apply 250-ft-lbs of torque on the nut. I confirmed this with my contact at Brophy Machine Works.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 11

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 12

Hello Brian, Thanks for finally finding an opportunity to write in. Yes, the B&W Continuum Weight Distribution System #BW78FR would be a great choice for your 2025 Ford Expedition Tremor with the HD towing package and your Rockwood Mini Lite…

view full answer...

Size Wrench Used to Install Brophy Hitch Ball # SC23-C

Product Page this Question was Asked From

Continue Researching