Correct Bearing Kit for a Lippert Trailer Idler Hub Part 122098

Question

Question:

Will this kit fit a Lippert 122098 hub? I have a Lippert 3500# axle with 122098 stamped on the back of the hub. Everything points to this kit but nothing positively confirms that. Aluma 8114BT utility trailer

asked by: Jason P

0

Expert Reply:

Yes, the Bearing Kit for #84 Spindles part # BK2-100 is correct for your Lippert Trailer Idler Hub part 122098. I confirmed this with Lippert for you as well.

expert reply by: Conner L

0

Answer 1

We have just the trailer hitch receiver you are looking for. I recommend the etrailer Trailer Hitch Receiver #e98909 you were looking at as it is a confirmed fit for your 2017 Chevrolet Colorado ZR2 4x4. The etrailer #e98909 has a tough matte black…

view full answer...

Answer 2

Most trailer wiring problems are the result of a bad ground. What I would do is start with the connectors. Maker sure the connectors on both the trailer side and vehicle side are free of dirt and corrosion and that they are properly grounded. Next, I…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 8

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 11

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Correct Bearing Kit for a Lippert Trailer Idler Hub Part 122098

Product Page this Question was Asked From

Continue Researching