Will the Curt Ball Mount for 2-1/2 Inch Hitches Fit a 2018 Ford F-350

Question

Question:

Will this Curt #c45459 2 1/2inch ball mount slid into the 2 1/2inch receiver on my 2018 Ford F-350 OK they claim some mount dont fit well? Thanks

asked by: Bill S

0

Expert Reply:

Yes, the Curt Ball Mount for 2-1/2" Hitches part # C45459 will fit the 2-1/2" receiver tube on your 2018 Ford F-350. As you mentioned, the Ford receiver tube tolerances can be off but the Curt ball mounts usually fit pretty well. The issues I am used to seeing are with the Draw-Tite and Reese ball mounts usually.

expert reply by: Conner L

0

Answer 1

While we don't carry the exact ball mount you are looking for we do have the Curt Ball Mount part #C45459 which fits the 2-1/2 inch hitch size and has a 6 inch drop.

view full answer...

Answer 2

In regards to the Curt Ball Mount for 2-1/2" Hitches part #C45459, the distance from the center of the hitch pin hole to the center of the ball hole is 9".

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 8

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Hey Ken! Instead of worrying about fitment and a potential return I can give you some measurements so you can figure it out before ordering. The standard shank on the B&W Continuum Weight Distribution System #BW28FR is 11-3/8" from the…

view full answer...

Answer 11

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 12

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Will the Curt Ball Mount for 2-1/2 Inch Hitches Fit a 2018 Ford F-350

Product Page this Question was Asked From

Continue Researching