How to Order Replacement Hardware for Draw Tite Hitch # 75876

Question

Question:

Hello, I need the install hardware kit for a draw-tite hitch #75876, I am installing it on a 2014 subaru forester 2.5 touring. Thank You

asked by: Tony

0

Expert Reply:

To order replacement hardware for a trailer hitch the part number you need is # RHK. On the product page of # RHK you'll select Draw Tite from the drop down menu and then enter part number 75876 and we'll ship you out the correct hardware.

expert reply by: Jameson C

0

Answer 1

The 3/8" Conical Tooth Washer #01292006-020-01 is the closest we have to a 7/16" inner diameter. We have the 7/16" Lock Washer #5-8 depending on if your application will work with this style washer. Otherwise you should be able to find…

view full answer...

Answer 2

The Reese Hitch 44680 is the same as the Draw-Tite Max-Frame Trailer Hitch Receiver part #75751 which is a fit for a 2012 Ford Escape. We can offer you replacement hardware using the Replacement Hardware Kit part #RHK which you will need to enter…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 6

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Hello John, thanks for reaching out. Yes, we do have a Thule roof rack that will allow you to install the Hullavator #TH898 on your 2015 Subaru Forester. For that I recommend the following: - Thule WingBar Evo Roof Rack for Raised Rails - Aluminum -…

view full answer...

Answer 10

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 11

Hey Ash, thanks for reaching out. That’s a solid build you’re putting together. For a Northern Lite 10-2 on a CM flatbed with a Ram 5500, you’re going to want the short TorkLift FastGuns #TLS9520. On flatbed setups like yours, the tie-down points are…

view full answer...

Answer 12

You could do that if you wish, you'll just want to make sure that the heat shield is NOT sandwiched between the hitch and the chassis of the vehicle at any point. We frequently hear from folks with concerns about the vehicle being harmed because…

view full answer...

How to Order Replacement Hardware for Draw Tite Hitch # 75876

Products Featured in This Question

Continue Researching