Available Sizes of Spindle Nuts and Nut/Washer Kits

Question

Question:

Can you get this kit for a 3/4 inch spindle rather than the 1 inch spindle?

asked by: Kristopher

0

Expert Reply:

The smallest spindle nut/washer kits we carry are for 1-inch spindles like # TRU94FR which are typically found on 2000-lb axles. We do offer a 7/8-inch inner diameter spindle nut # 165931 by itself but nothing for a 3/4-inch spindle as might be found on a small import trailer.

expert reply by: Adam R

0

Answer 1

Hey Ethan, thanks for reaching out. The correct bearing and seal kit for your Dexter 7,000 lb axles is going to be either the Bearing Kit part #BK3-210 which has a 2.125" seal or the Bearing Kit part #BK3-200 which has a 2.250" seal. This…

view full answer...

Answer 2

To determine what the correct replacement hubs are for your Magic Tilt trailer there is a little bit of information that we will need. We will need to find out inner diameter of both the Inner and Outer Bearings as well as the inner diameter of the…

view full answer...

Answer 3

We have the grease seal you are looking for. Our part number #GS-2250DL is the same as the Dexter 010-054-00 that you have. The inner diameter of this seal is 2.25 and the outer is 3.376 inches.

view full answer...

Answer 4

I am going to recommend disassembling one of your hubs to verify these parts are going to be correct for your Kelsey/Hayes axle. It sounds like you are going to have a 3,500lb axle which have all used a fairly standard size brake and hub. The…

view full answer...

Answer 5

Hey Grae; that doesn't seem to be a complete serial number so I won't be able to identify it with that information. I would pull the existing hubs and see if the bearing numbers are stamped into the sides of the bearings to try and identify…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Available Sizes of Spindle Nuts and Nut/Washer Kits

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching