Which Tonneau Cover Should be Used on 2012 Ford Super Duty Long Bed with Tool Box in Bed

Question

Question:

Need length of side rails to see if it would fit on 8ft box with tool box in it. I have 77” behind tool box

asked by: Stephen M

0

Expert Reply:

For your 2012 Ford F-Series Super Duty with a long bed we have a tonneau cover that is specifically designed for fitting behind a tool box with the Access Toolbox Edition Cover part # 834532008460 which will fit and work well as long as your tool box width is between 19 and 21 inches in width. The Truxedo you referenced only fits the short bed versions of your truck so I can not recommend it for your long bed truck.

expert reply by: Jameson C

0

Answer 1

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 2

Hey Doug! The Firestone Ride-Rite Air Helper Springs #F35FV are the right kit for your 2026 Ford F-350 FX4 dually. However, you will need to measure to be sure it fits. The distance from the top of your rear axle to the top of the jounce bump stop…

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 5

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 6

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 7

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 8

Hey Mark, since folding tonneau covers like the etrailer part #e73DR end up adding height to the top of the bed rails near the front of the bed they are not ideal for towing a fifth wheel trailer as the nose of the trailer is most likely going to…

view full answer...

Answer 9

Hey Chris, No, there isn't an upgrade kit for your Generation 1 MORryde StepAbove RV Steps to make them a Generation 2. There is a Replacement Leg for MORryde StepAbove RV Steps - 2nd Generation #MR36DR, but because the Generation 1 steps'…

view full answer...

Answer 10

Hi Bruce! The Access Toolbox Edition Soft, Roll-Up Tonneau Cover #A63FR will indeed fit your 2021 GMC Serra 1500 SLT with the short bed and your toolbox. This can be used with toolboxes that measure 19" to 21" long, so you are good to go!…

view full answer...

Answer 11

Hey Daniel congrats on the new truck! The Lomax Stance Hard Tonneau Cover item #LOM54RV does indeed fit the 2026 Chevrolet Silverado EV with the Mid Gate. It also works with the Multi-Flex Tailgate that comes on the Trail Boss models. For a…

view full answer...

Which Tonneau Cover Should be Used on 2012 Ford Super Duty Long Bed with Tool Box in Bed

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching