Installation Hardware Bolt Size for 2009 Hyundai Santa Fe Frame

Question

Question:

What size are the frame bolts 2009 Hyundai Santa Fe

asked by: Rob

0

Expert Reply:

The Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" # 75471 uses the frame bolts that are M10 X 1.25 X 30mm CL10.9 and then 7/16 inch lock washers and 3/16 x 1.00 x 2.00 blocks. This connects to the existing weldnuts in the vehicle frame.

I've attached the installation instructions and a video to assist.

expert reply by: Jason S

0

Answer 1

Since what you have is the Thule Chariot the correct replacement flag is actually the part #TH77HH.

view full answer...

Answer 2

To install the Curt hitch part #13571 the two bolt sizes needed are M12-1.25x40 and M10-1.25x35 which are included. If you need new bolts you can order them from us as part #RHK.

view full answer...

Answer 3

Hey I am sorry to hear that David. A damaged weld nut really sucks but it does happen on rare occasion. You could try using a thread tap to repair the threading on the nut, but in all likelihood, the weld nut is toast. In this case you will have to…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 8

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 9

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 10

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Installation Hardware Bolt Size for 2009 Hyundai Santa Fe Frame

Featured Help Information

Miscellaneous Media

Continue Researching