Fulton Trailer Hinge Replacement Bolt Size

Question

Question:

Will this fit the FULTON 3 x 3 Trailer Hinge Coupler? I need a replacement BOLT and nut. NOT PIN.

asked by: Paul M

0

Expert Reply:

We don't carry the replacement bolt you'd need for the Fulton Fold-Away Coupler Hinge Kit # FHDPB330301 but the bolt is a 5/8 inch diameter Grade 5 bolt so your best bet would be to find a nut and bolt that matches that at a local hardware store. You'll want to use a lock nut too.

expert reply by: Jameson C

0

Answer 1

Thanks for sending pictures! The titanium shims you installed are just fine, but note that the inch of play is absolutely normal per my contact at Cequent Corporation. The Fulton Fold-Away coupler hinge kit you referenced is most likely very similar…

view full answer...

Answer 2

I went out to the warehouse and pulled one of the Pro Series Snap-Ring Swivel Jacks, #PSEJ10000101, to measure for you. I added dimensions to a photo I took of the mounting plate for you to use to see if the mounting pattern will match up to your…

view full answer...

Answer 3

Most likely you need to go with the Reese Landing Gear Set #RP500708 because it has the typical inside to inside and outside to outside spacing of 15-1/2" and 17-1/2" respectively. This is the most common weld stop measurements which is why…

view full answer...

Answer 4

Aside from the weight capacity of the jacks and their speed, they also have different mounting bracket locations. If you don't mind potentially having someone do some cutting and welding on your trailer then either one will work great for you. If…

view full answer...

Answer 5

While I don't know exactly what landing gear you have on your 2011 Keystone Raptor 3812 Toy Hauler, I can say that you should be able to replace them with the Landing Gear Set w/ Handle #RVLG-8HDL as this landing gear uses the standard weld mount…

view full answer...

Answer 6

Hello Larry, thanks for reaching out. Yes, the Curt Class 3 Hitch #C77NR will indeed fit your 2025 Kia Niro PHEV. I double checked with Curt and they do confirm this hitch fits all models of the 2025 Kia Niro EV and this includes the PHEV model. What…

view full answer...

Answer 7

I attached a picture that has about every dimension you could want for the part #BD500217. The overall length is 17 inches and the diameter of the screw is 1-1/4 inches.

view full answer...

Answer 8

A specific dimensional drawing of the replacement screw and nut #BD500217 is not available for proprietary reasons. I can tell you that the diameter of the threaded parts is 1-1/4 inches. It was specifically designed for 12K Bulldog jacks, series…

view full answer...

Answer 9

Two red dots on the display of the Primus part #TK90160 indicate that the controller is on but a trailer is not detected. Since you are seeing that with multiple trailers connected you most likely have corrosion or dirt built up on the brake output…

view full answer...

Answer 10

Two dots will be displayed on your now discontinued Draw-Tite I-Command Trailer Brake Controller 5535 whenever a trailer is not connected. After 15 minutes of no motion the controller goes into power-saving mode and the display will be completely…

view full answer...

Answer 11

I do have a solution for your 2024 Kia Telluride that has the LED taillights that does allow it to have both a 4-way and 7-way plus install a brake controller but it is not with the #TK74CR which does not work for you based on the LED taillights.…

view full answer...

Answer 12

No, the Tekonsha OEM Replacement Vehicle Wiring Harness w Brake Controller Adapter #TK74CR will unfortunately not work with your 2023 Kia Telluride with LED lights. Your best bet would be to use a universal wiring harness #C59236 which will work with…

view full answer...

Fulton Trailer Hinge Replacement Bolt Size

Continue Researching