Rear Ramp Door Spring Assist Maintenance

Question

Question:

Do you have to do anything to maintain these type of springs? I dont think the make is important but Mirage MXL 2017 car hauler, sorry no way to add pic

asked by: Greg

1

Helpful Expert Reply:

The Enclosed Trailer Ramp Spring # CB250D96SHD are just like garage springs. There is nothing really required to maintain them other than visual inspection and light grease on the moving parts. If they lose tension or require cable maintenance, it is recommended to have a garage door professional do the work on them due to the high tension.

expert reply by: Jason S

1

Answer 1

The spring with the black cable drum should always be mounted to your LEFT, standing on the inside of the trailer looking out. This is very important for proper operation. Dual spring systems, like #ERS160D96, have a red-coned and a black-coned…

view full answer...

Answer 2

Happy to help James, thanks for reaching out! Choosing the right M-3 ramp door spring system really comes down to matching your specific trailer and door. The biggest factor is the weight of your ramp door. The spring system is designed to help lift…

view full answer...

Answer 3

The Replacement Drum for M-3 Dual Ramp Springs - Right Hand #DRUM-M-3RH or the Replacement Drum for M-3 Dual Ramp Springs - Left Hand #DRUM-M-3LH is what you are seeking. You also want the Replacement Cables for Conventional Ramp Door Spring -…

view full answer...

Answer 4

The best thing you can do to eliminate those streaks is regularly clean your trailer because there just is not a way to re-route the condensation before it leaves streaks. The best way to do this is by using the Griot's Garage Rinseless Wash and…

view full answer...

Answer 5

When selecting ramp springs for a trailer ramp, you will want to know the diameter of your hinge pin and how much space you have available in the hinge. A typical horse trailer or utility trailer ramp uses 3/4 inch hinge pins and would require two…

view full answer...

Answer 6

Hey Dan; there isn't an actuator that will slide in place for a replacement of your Tie Down 80LP, you'd have to go with a new actuator. From what I can find, this actuator bolts onto a 3" wide channel tongue, so you can replace it with…

view full answer...

Answer 7

I'd go with a double spring personally, Scott. These are typically going to be used on more heavy duty applications like your enclosed trailer with a pretty heavy door. In order to get a proper replacement though, you'd need measure the width…

view full answer...

Answer 8

Hey Rodney! Congrats on your new trailer! If you door weighs 250 lbs or less the Conventional Ramp Door Spring for 8' Wide Enclosed Trailer item #CB250D96SHD will perfectly. You'll just need to trim the shaft down to fit your trailer's…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 12

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Rear Ramp Door Spring Assist Maintenance

Product Page this Question was Asked From

Continue Researching