Mounting Plate Recommendation for Fulton XP Trailer Jack

Question

Question:

I have a bass cat trailer and do not have the hardware to mount the jack and for some reason cannot find out exactly what hardware is needed. Seems to be some sort of bushing and a nut combo.

asked by: Lynn W

0

Expert Reply:

The picture you submitted looks like the mount of a Fulton XP jack part # FXP15W. Which if you are looking for a replacement mount you'd want the part # F500349.

expert reply by: Jameson C

0

click to enlarge

Answer 1

The left side is the driver side, right side is passenger side. On a trailer brake assembly like #23-105 the arm that the magnet is on points to the front of the trailer and the magnet always will be on the bottom. I have included a picture that…

view full answer...

Answer 2

Richard, to replace your UFP HD-1377-10 hub and drum you can use the Dexter Trailer Hub and Drum Assembly for 3,500-lb Axles #84546UC3, the Dexter Nev-R-Adjust Electric Trailer Brakes #23-468-469, and the mounting hardware #BRKH10B.

view full answer...

Answer 3

I have an option for you, but since Shelby is out of business you will not be able to purchase another Model 5856A jack. Instead I recommend replacing it with the Fulton Round, Snap-Ring Swivel Marine Jack - Weld On - Sidewind - 10" Lift - 1,200…

view full answer...

Answer 4

What we have heard is that the Fulton #FTJ120W0301 does fit the mounting plate of the Shelby Jack 5784 which is what it looks like you have something similar to.

view full answer...

Answer 5

Parts are no longer available for the old Fulton Magnum jacks unless it is one of the following jack models: TJ503/C, TJU503, PMJ53, TJ507/C, PMJ75, CS750, GR700/TJ712, XP10/6/W/WC and XP100. Then you would use #F0933302S00. But we do have parts for…

view full answer...

Answer 6

It sounds like you're needing a jack like the Fulton Bolt-Thru Swivel Marine Jack #FXP10W0301 which installs on trailers that already have the mount welded on with a single bolt attachment for the jack itself (like what we see with part…

view full answer...

Answer 7

Since we do not have a Shelby jack mounting bracket that goes to the discontinued Shelby Jack #5876A8, I have no way to confirm whether or not a Fulton jack will fit it. With that being said, the Fulton Bolt-Thru Swivel Marine Jack #F1411300301 is…

view full answer...

Answer 8

In regards to the Fulton XLT Bolt-Thru Swivel Trailer Jack part #F26ZR, the distance from the center of the mounting bracket to the top of the jack tube cap is 13.4". I have attached a photo below as well to show this. I spoke to Fulton and this…

view full answer...

Answer 9

Fulton's snap-ring jacks like the #FTJ120W0301 are going to top out at 1,200lbs and the 1,500LB Jack #F141132 you found has a bolt-thru design and is not offered in a snap ring. We do offer the 2,000LB Jack #TJB-2002S-B which would fit your…

view full answer...

Answer 10

The Fulton jack part #F141132 that you referenced is a really great jack that I know you'll be happy with, but it requires the bracket part #P9012-00 to mount to a trailer which isn't the same as what you have now. So your best option is to…

view full answer...

Answer 11

For your welded plate, the Replacement Bolt-On Mounting Kit for Fulton XP Series Jack #F500349 sounds like what you are describing but it isn't a welded plate. If that is similar to what you have, then I recommend the Fulton Bolt-Thru Swivel…

view full answer...

Answer 12

There are a few solutions for your tailgate to clear the jack on your trailer. I recommend to use a longer ball mount like #D-26, that would move the trailer back further away from the truck and give you clearance you need. If you know what size the…

view full answer...

Mounting Plate Recommendation for Fulton XP Trailer Jack

Continue Researching