Length of StabiLoad Support on HitchMate Cargo Stabilizer Bar

Question

Question:

What is the length of the stabiload attachment?

asked by: Chip V

0

Expert Reply:

The StabiLoad Support that comes included with the HitchMate Cargo Stabilizer Bar # HE4016-4017 measures 14 inches long from where it attaches to the expandable bar to the end of the support. I have attached an image to assist.

I have also included a short video demonstration on this product that you can check out.

expert reply by: Chris R

0

click to enlarge

Answer 1

The cross bars for the Invis-A-Rack Folding Ladder Rack - Black Powder Coated Aluminum - 500 lbs Item #DZ951600 are aluminum but the center portion of the cross tube is the only part that is square. The cross bar span is 69". The manufacturer is…

view full answer...

Answer 2

The DeeZee Invis-A-Rack Folding Ladder Rack that you need for the 2015 Ford F-250 Super Duty 8 foot bed is part #DZ951800. The DeeZee Invis-A-Rack Folding Ladder Rack part #DZ951600 fits the 6-3/4 Foot Bed. There used to be a TruXedo Lo Pro Soft…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Congrats on the new motorhome Edward! SnapPad doesn't have the 2026 Allego Red 38 KA in their system so I don't know what size your jack feet are. However, we have a few options that will work with the HWH leveling systems. What you'll…

view full answer...

Answer 11

Unfortunately you can not Doug. The factory hitch on your 2020 Ford F-150 Lariat is part of the rear step-bumper assembly. It's bolted to your frame and then the step-bumper bolts to the trailer hitch. Removing the factory hitch removes the…

view full answer...

Answer 12

Hey Wayne! The answer to your question is maybe. As you know, the Curt #C14017 is designed for the F-150 without the factory hitch. Typically this is because the factory hitch is integrated with the bumper and removing it to replace it with the…

view full answer...

Length of StabiLoad Support on HitchMate Cargo Stabilizer Bar

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching