How Does Hand Brake on Dutton-Lainson Hand Winch Work?

Question

Question:

In your web link above, does the Dutton-Lainson Hand Winch,TUFFPLATE Finish, Two Speed with Direct Drive - Hand Brake - 2,500 lbs # DL14830 ratchet in both directions? You recommended this winch for an application where the customer is pulling up then reversing to lower down a trailer on an incline. On the winch, how do you actually reverse to the lowering position and safely reverse the direction of the pull? Is the ratchet released putting the winch in free wheel and the hand brake is used to control the reversed momentum?

asked by: Hunter S

1

Helpful Expert Reply:

The Dutton-Lainson Hand Winch - TUFFPLATE Finish - 2 Speed - Direct Drive - 2,500 lbs # DL14830 will only ratchet when being pulled in. The output will free-wheel and allow you to control that free-wheel speed with the integrated hand brake. The hand brake will put friction on the free wheeling cylinder to slow the pull and help you control the reversed momentum. To switch into that reverse function from the ratcheting you simply will apply a little tension to the handle and then remove the flip the ratcheting pawl away from the gear.

expert reply by: Jason S

1

click to enlarge

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Hey Bryan, that's a good question. The pricing can definitely be misleading, but I wouldn't use it to judge the quality of the tire. A lot of that comes down to promotions, inventory, and whether you're looking at a tire by itself or…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

The 5.30-12 tires, being wider, are going to make more contact with the road. This means that the noise, and heat build up will be higher than a 4.80-12 tire but the rolling resistance will actually be less because the tire is larger diameter. The…

view full answer...

Answer 8

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 11

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

How Does Hand Brake on Dutton-Lainson Hand Winch Work?

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching