No Brakes on New Haulmark Trailer with 2003 Dodge Ram 2500
Updated 01/28/2019 | Published 01/25/2019 >
Products Featured in This Question
Question:
I have an 03 Dodge 2500 with a factory brake controller which has worked with all my other trailers. I just purchased a new Haulmark enclosed trailer with Dexter axles, and the brake controller doesnt recognize that the trailer is hooked up. The brake controller doesnt apply the brakes either. Do I need to purchase a new controller or is there something going on.
asked by: Zeke
Expert Reply:
What type of brakes are on your new trailer? If they are hydraulic and you are using an electric over hydraulic actuator then this very well may be your issue as the factory brake controller on a 2003 Dodge Ram 2500 is not compatible with electric over hydraulic brakes. If this is a Titan the part is T4845900 for Titan actuators or you will need a new brake controller like the Tekonsha Prodigy P2 Trailer Brake Controller part # 90885 with the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers part # 3020-P.
If your new trailer has standard electric brakes then the first thing we are going to need to do is test the brake controller and wiring on the vehicle side. In order to do this you are going to need to test the 5 o'clock pin on the 7-way with a multimeter while the manual override is applied. You should be seeing close to 12 volt here. If you do not then you know there is an issue with either the vehicle wiring or brake controller. The brake output wire at the back of the 7-way will need to be traced as far as possible while checking for shorts but if none are found on the visible portion then you will need to take the vehicle to your local dealer for troubleshooting.
I understand the trailer is new but that still does not mean it is exempt from trailer wiring problems therefore you will need to test and inspect the brake output wire on the trailer as well as inspecting the trailer connector. If you have access to a different truck/trailer you can narrow down what side the issue is occuring on.
Continue Researching
- Search Results: 023~216~00
- Q&A: Is It Better To Replace The Brake Shoes Or Completely Replace The Brake Assembly
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 10" - Left/Right Hand Assemblies - 3.5K
- Shop: Easy Grease Trailer Hub and Drum Assembly for 3.5K Axles - 10" - 5 on 4-1/2 - Pre-Greased
- Shop: Dexter Electric Trailer Brake Assembly - 10" - Left Hand - 3,500 lbs
- Shop: etrailer Electric Trailer Brakes - 10" - Left/Right Hand Assemblies - 3,500 lbs
- Shop: etrailer Electric Trailer Brakes - Self-Adjusting - 12" - Left/Right Hand - 5.2K to 7K
- Shop: Trailer Hitch
- Shop: Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Wiring
- Search Results: trailer tires and wheels
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Shop: Suspension Enhancement
- Video: Review of etrailer Trailer Hubs and Drums - Hub with Drum - AKHD-545-35-EZ-K
- Search Results: trailer wiring
- Q&A: What is a #84 Spindle and How Do I Know I Have One On My Trailer?
- Search Results: trailer jack
- Video: etrailer VS Dexter Self Adjusting Brakes Comparison
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Q&A: Instructions to Wire a Trailer for Electric Brakes
- Shop: Brake Controller
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Shop: Gooseneck Hitch
- Article: How to Measure for Trailer Hitch Drop