Replacement Studs for Trailer Hub # AH60880FCOMP

Question

Question:

I KNOW THE STUD DIAMETER FOR THESE HUBS IS 5/8. CAN YOU GIVE ME THE OTHER DIMENSIONS NEEDED TO ORDER REPLACEMENTS.

asked by: ANNETTE N

0

Expert Reply:

For replacement wheel studs for the Trailer Hub Assembly # AH60880FCOMP that you referenced you would want the # 7-232 and you'd be set. These are 2-3/4 inches long, 5/8 inch diameter and have a spline length of .31 inch.

expert reply by: Jameson C

0

Answer 1

Hi Robert! The 17-1/2" wheels are a bit more limited than other offerings, but I think you may be interested in the following two options: Americana Hub-Piloted Solid Center Wheel w -0.5" Offset - 17-1/2" x 6-3/4" - 8 on 6-1/2 -…

view full answer...

Answer 2

I have attached for you below a list of all our 17.5" x 6.75" trailer wheels with an 8 on 6-1/2" bolt pattern below. There are a few different types of wheels in this list such as aluminum/steel, dually/standard, and hub/lug centric.…

view full answer...

Answer 3

The Taskmaster Modular Wheel w/ +0.08 Offset - 17-1/2" x 6-3/4" Rim is offered in both silver as part #TA35ZR and white as part #TA36MR. That said, they are designed for use with 5/8" wheel studs. The only 17-1/2" wheels we offer…

view full answer...

Answer 4

Hey Robert, To find your offset you'll need to measure from the mounting surface of your lugs to both outer edges of your current wheels. A negative offset will move the tire further away from the trailer while a positive offset brings the tire…

view full answer...

Answer 5

A Dexter 8k hub would have an 8 on 6-1/2 inch bolt pattern like what the part #TA45ZR has. This is also a 17.5 inch diameter trailer wheel. For a mod style wheel instead, we have the part #TA35ZR.

view full answer...

Answer 6

It might be possible to change out the studs in your hub from 9/16 to 5/8 if they are drive-in studs and not the type that threads in. If they are drive in and the diameter of the knurl end is approximately 0.6875 inches then you can replace them. We…

view full answer...

Answer 7

Hey Don. The Taskmaster Modular Wheel item #TA35ZR works with 5/8" lug studs. It does not have a center cap. The pilot hole diameter is 4.76". This is a 17-1/2" wheel with a 8 on 6-1/2 bolt pattern. It has a 5,956 lbs capacity per…

view full answer...

Answer 8

The Americana Modular Wheel #AM22461 shares the same dimensions as your SRW 31767A0 trailer wheel. It has the same 17.5" x 6.75" size with 8 on 6.5" bolt pattern and -0.5" offset. It also has the same 6,005lbs capacity with…

view full answer...

Answer 9

You can potentially change wheel/tire size if you have the clearance but you can gain load capacity more easily by keeping your existing rims and switching to a Load Range G tire in your current size ST235/80-16. Westlake Load Range G radial tires…

view full answer...

Answer 10

You will want to stick with the same style of lug nut, so if you use 90 degree lug nuts, stick with that. The reason is the taper on the 60 degree lug nut is steeper, so there could be fit issues depending on your trailer wheel, as they are designed…

view full answer...

Answer 11

I spoke with Phoenix USA and they let me know the inner diameter of the Phoenix USA QuickTrim Hub Cover #PXQT965CHN is 8" and the cylinder section that would allow the axle to slide up in is 5”.

view full answer...

Answer 12

A negative offset like the offset on the Americana Modular Wheel w/ -0.5 Offset - 17-1/2" x 6-3/4" Rim - 8 on 6-1/2 - Silver #AM22461 reduces the back-spacing. Since this is a 6-3/4" wide rim that means the back-spacing is 3-7/8"…

view full answer...

Replacement Studs for Trailer Hub # AH60880FCOMP

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching