Lug Hole Dimensions of 17-1/2 Inch Taskmaster Solid Center Wheel

Question

Question:

lug hole size?

asked by: Adrian

1

Helpful Expert Reply:

The Taskmaster Solid Center Wheel LT2524SP (discontinued and replaced by the part # TA45ZR) has a 5/8" lug hole size. You'll need to use a 5/8" Flange Wheel Nut # 95188 to secure the wheel to your trailer hub.

expert reply by: Jon G

1

Answer 1

Hi Robert! The 17-1/2" wheels are a bit more limited than other offerings, but I think you may be interested in the following two options: Americana Hub-Piloted Solid Center Wheel w -0.5" Offset - 17-1/2" x 6-3/4" - 8 on 6-1/2 -…

view full answer...

Answer 2

The Taskmaster Modular Wheel w/ +0.08 Offset - 17-1/2" x 6-3/4" Rim is offered in both silver as part #TA35ZR and white as part #TA36MR. That said, they are designed for use with 5/8" wheel studs. The only 17-1/2" wheels we offer…

view full answer...

Answer 3

Hey Robert, To find your offset you'll need to measure from the mounting surface of your lugs to both outer edges of your current wheels. A negative offset will move the tire further away from the trailer while a positive offset brings the tire…

view full answer...

Answer 4

I have attached for you below a list of all our 17.5" x 6.75" trailer wheels with an 8 on 6-1/2" bolt pattern below. There are a few different types of wheels in this list such as aluminum/steel, dually/standard, and hub/lug centric.…

view full answer...

Answer 5

A Dexter 8k hub would have an 8 on 6-1/2 inch bolt pattern like what the part #TA45ZR has. This is also a 17.5 inch diameter trailer wheel. For a mod style wheel instead, we have the part #TA35ZR.

view full answer...

Answer 6

It might be possible to change out the studs in your hub from 9/16 to 5/8 if they are drive-in studs and not the type that threads in. If they are drive in and the diameter of the knurl end is approximately 0.6875 inches then you can replace them. We…

view full answer...

Answer 7

No, it still matters Mike. The Hub-Piloted Solid Center Wheel w -0.5" Offset item #AM32NR still relies on the lug nuts to center the wheel on the hub. Using 9/16" lug studs with 5/8" holes is going to cause wobble and you'll break…

view full answer...

Answer 8

Hey Don. The Taskmaster Modular Wheel item #TA35ZR works with 5/8" lug studs. It does not have a center cap. The pilot hole diameter is 4.76". This is a 17-1/2" wheel with a 8 on 6-1/2 bolt pattern. It has a 5,956 lbs capacity per…

view full answer...

Answer 9

You are right that there are a few common stud sizes available on trailer hubs, and the difference has to do with what size wheels they are designed to work with. Larger studs are generally for larger/heavier wheels. You do need to ensure…

view full answer...

Answer 10

The closest open acorn nut we offer we offer to what you want is the part #X1148. This nut will fit a 5/8 inch stud except it is designed to be tightened with a 15/16 inch wrench. I attached a page that has all of the 5/8 inch open acorn nuts we…

view full answer...

Answer 11

What is the width of the wheel? In order to determine what offset you have I would need to know the current width so I can see what your 4.5 inch dimension indicates. A zero offset means the hub face dimension is perfectly centered so I would need…

view full answer...

Answer 12

If you keep the trailer tires inflated to the maximum psi indicated on the tire sidewall then they should not bow out on the sides enough to cause any clearance problems between the tire and the trailer. A 1/2 inch space could be enough but it is…

view full answer...