Can Fulton Winch Cable # FWC7500100 be Used with Fulton Winch # F142430

Question

Question:

Can I use cable number WC7500100 on Fulton winch part# 142430?

asked by: Laura P

0

Expert Reply:

Yes, the Fulton Galvanized Winch Cable # FWC7500100 will work perfectly with the Fulton High-Performance 2-Speed Trailer Winch # F142430. I have attached a short video demonstration that you can also check out.

expert reply by: Chris R

0

Answer 1

The best option we carry for a 10,000 lb boat is the Fulton High-Performance 2-Speed Trailer Winch #F142430 which has a 3,700 lb capacity with Cable #FWC7500100. The winch to boat size capacity is 2-to-1 though it can also be 3-to-1 if you have…

view full answer...

Answer 2

Thank you for all that information and while I can understand not wanting to go with an electric winch for a boat trailer, the issue is the weight of your boat as well as the fact you are using bunks and have a steep incline. Even if you had a very…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 10

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Can Fulton Winch Cable # FWC7500100 be Used with Fulton Winch # F142430

Featured Help Information

Miscellaneous Media

Continue Researching