Installing Brophy Tailgate Scissor Step Mounting Bracket # TSSB

Question

Question:

Picture not very clear to me. Are you saying the step bracket is screwed into the tailgate top edge or as the gate is laying open, to that edge of the now flat surface?

asked by: Eric D

0

Expert Reply:

When installing the Brophy Tailgate Scissor Step Mounting Bracket # TSSB you will first measure the distance between the two pins on the bracket, on center. Then with your tailgate open and laying flat, you will take a 5/8 inch measurement in from the edge of the tailgate and this is where you will drill the two 7/16 inch diameter holes, spaced apart the distance that you took when measuring the pins on the bracket.

I went out to our warehouse so I could take a picture of the instructions that will come with the bracket. I have attached the image below that you can also take a look at.

expert reply by: Chris R

0

click to enlarge

Answer 1

The Brophy Scissor Step Bracket #TSSB will install on the edge of your tailgate. You will have to drill two holes for the L shaped pins. After drilling, all you have to do is simply insert the L pins into those holes and attach you Brophy steps! For…

view full answer...

Answer 2

I may have different installation method for you, but there is not an extended bracket made to push the TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear #TLA7843 away from your camper to clear your bumper. It may be possible to have a…

view full answer...

Answer 3

The steps on the TorkLift GlowStep Revolution Scissor Steps #TLA8003 referenced in your question feature a vertical height of 13-3/4 inches to 14-3/4 inches when fully collapsed in their stored position. This is a really nice, 3-step scissor step…

view full answer...

Answer 4

The Torklift steps part #TLA7834 would be your best option. These steps have a height of 35-5/8 inches from where they mount down to the ground when folded out so this would match your 35 inch dimension perfectly.

view full answer...

Answer 5

view full answer...

Answer 6

If the Brophy stairs #SS02 have to open to uneven ground then using something to support the side not touching the ground is a good idea. There are a lot of things you could use but I recommend keep a set of leveling blocks #CAM44512 with you for…

view full answer...

Answer 7

Hello Tom. The TorkLift GlowStep Stow N' Go Scissor Steps w/ Landing Gear #TLA7834 will fit your 2023 Lance 825 truck camper, but you will need to install the bracket that comes with the step. There is no guarantee that your current bracket will…

view full answer...

Answer 8

The Brophy Camper Scissor Steps part #AS24 will require 1-1/4" of clearance between the bottom of the door and bottom of the cab on your Palomino Truck Bed Camper in order for the mounting bracket to attach. If you removed a portion of the trim…

view full answer...

Answer 9

Both the Brophy #AS24 and the TorkLift #TLA7804 are easily removed when not in use- and it's actually recommended that you do so. Additionally, they both weigh in around 26-lbs total, so they're easy to move on and off; so they'd both be…

view full answer...

Answer 10

I am not sure what steps you currently have, but we do carry step options that can reach further down or have the legs extended for those instances. The legs can also be extended as one or the other, so if the ground is uneven and you need the right…

view full answer...

Answer 11

I recommend using the TorkLift GlowStep Camper Scissor Steps w/ Landing Gear - 4 Steps - 20" Wide - 375 lbs #TLA7804-8000. These are a 4 step system that has glow tape on the steps to help with visibility at night, and the adjustable landing…

view full answer...

Answer 12

The TorkLift GlowStep Stow N' Go #TLA7844 weighs just over 30 (about 32) lbs by itself. The TorkLift GlowStep part #TLA7804 and part #TLA7504 both weigh a little over 20 (about 22) lbs each.

view full answer...

Installing Brophy Tailgate Scissor Step Mounting Bracket # TSSB

Product Page this Question was Asked From

Continue Researching