Offset Gooseneck Ball Recommendation for Draw Tite Hitch in 2016 Ram 3500

Question

Question:

Hi have a 2016 Ram Mega cab short bed. I have the Reese hitch. Do you have a hitch extender that would work for this set-up?

asked by: Holly

0

Expert Reply:

If the gooseneck hitch you had was the Draw Tite Hide-A-Goose style of hitch the offset gooseneck ball part # 19308 would fit and work well. The hitch you'd have to have installed in your 2016 Ram 3500 would be the part # 9466 which is the correct fit for your truck. Reese does not make a gooseneck hitch for your truck but Draw Tite and Reese are made by the same company.

expert reply by: Jameson C

0

Robert

2/3/2020

I have a 2016 ram 3500 dually. Original puck system. Will tje 5, curt offset bsll C602 fit?

Jacob H.

2/5/2020

The Curt 4 inch offset goose ball will not work with an OEM puck system gooseneck hitch. We do not currently offer an option for an offset for factory puck systems.

Answer 1

Yes, the Hide-A-Goose Underbed Gooseneck Trailer Hitch item #9466 is compatible with the Reese Goose Box 5th-Wheel-to-Gooseneck Air Ride Coupler Adapter item #RP85FR. It has a 30,000 lbs capacity and locks inside the base similar to other gooseneck…

view full answer...

Answer 2

The Hide-A-Goose Underbed Gooseneck Trailer Hitch - 30,000 lbs #9466 does not have an adapter that fits in the gooseneck underbed system. It would require an above bed adapter. The underbed systems that work with the hitches have pins that run all…

view full answer...

Answer 3

Thank you for the photos! You have the Hide-A-Goose Underbed Gooseneck Trailer Hitch #9466 installed on your 2018 Ram 3500 so to replace the hitch ball you just need the following part: - Replacement Ball for Reese Elite Series and Factory Ford and…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 8

Hey Kyle! That is correct. The Coleman-Mach Mach-C Everest has variable-speed cooling and an inverter-driven compressor. However, the Mach-C Everest uses a traditional wall thermostat instead of a remote control. It also works with both ducted and…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

Hi Glen, It will depend on what the GVWR (gross vehicle weight rating) is of your trailer to determine which B&W 5th wheel to gooseneck adapter will work best for you. Fifth wheels and gooseneck trailers go off of pin weight instead of tongue…

view full answer...

Answer 11

Hey Judy, normally when this occurs with a truck bed camper the issue is that there happens to be too much weight in the back of the truck camper behind the rear axle. Can you try moving any of that weight forward in the camper when on the road and…

view full answer...

Answer 12

Hey George, welcome back. I double checked with the manufacturer and the Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box item #GY38FR is the correct option to replace your MORryde part number SPB72-1621HD. It works with pin weights from…

view full answer...

Offset Gooseneck Ball Recommendation for Draw Tite Hitch in 2016 Ram 3500

Product Page this Question was Asked From

Continue Researching