Thread diameter and pitch for the Replacement Knob for Thule Professional Ladder Tilt # 853-5714

Question

Question:

Replacement Knob for Thule Professional Ladder Tilt What is the thread specification for this knob? Does it match the THULE Stainless Steel T-bolt 853-5648?

asked by: Michael P

0

Expert Reply:

The Replacement Knob for Thule Professional Ladder Tilt, # 853-5714, will accept an M8 x 1.25 thread pitch bolt and is designed to be used with the M8 x 1.25 x 25 mm Carriage Bolt for Thule and DeWalt Contractor Series Ladder Lift.

The replacement knob does not work with the Thule Stainless Steel T-bolt, # 853-5648.

expert reply by: Robert G

0

Answer 1

The Thule knob #853-5714 is not a confirmed fit for the TracRac load stops. The Thule knob will accept an M8 x 1.25 thread pitch bolt and is designed to be used with an M8 x 1.25 x 25mm Carriage Bolt. The bolt on the TracRac load stops is a 3/8 - 16…

view full answer...

Answer 2

The thickness of the T-bolt head of the part #Y8880184 you referenced is 5/32 of an inch. I attached a picture that has all of the other dimensions as well. These T-bolts are M10 x 1.5 x 25

view full answer...

Answer 3

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 4

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

Hi Curtis! We have you covered! Pun intended. ^___^ What you are looking for are the following parts: Pace Edwards Full-Metal JackRabbit Retractable Hard Tonneau Cover w Explorer Rails - Aluminum #PE36CV Pace Edwards Contractor Rig Rack Truck Bed…

view full answer...

Answer 9

Hey Dennis, In terms of the puck system, the layout of the pucks between the 2 bed sizes are going to differ. Since they don't make a fixed hitch for the puck system on that 8.9 foot bed you would have to go with a slider if you wanted to use the…

view full answer...

Answer 10

Since wire color codes are NOT universal, we always recommend wiring by function, rather than wire color. If you look at the Trailer Wiring FAQ article I have linked you to, you can see some diagrams showing the proper way to wire a vehicle and…

view full answer...

Answer 11

Got you covered Pete, thanks for reaching out! For your 26 Chevy 2500HD, the Curt EZr Double Lock Underbed Gooseneck Hitch #C65HR has the best overall value between cost effectiveness and towing capabilities. The Curt EZr is rated for 30k lbs, so it…

view full answer...

Answer 12

Hi Taylor, I pulled up the B&W Tow and Stows with the pintle and it looks like they don't have an option that has a 9-inch drop. The only options for a 2.5" hitch receiver is the BW77BR you were already looking at with a 6" drop.…

view full answer...

Thread diameter and pitch for the Replacement Knob for Thule Professional Ladder Tilt # 853-5714

Products Featured in This Question

Product Page this Question was Asked From

Continue Researching