Replacement 5-Function Remote Receiver With Fuses

Question

Question:

Where is the location of this on my RV? I purchased the new switch for levelers and was told to replace this board.

asked by: Bonnie L

0

Expert Reply:

The Replacement 5-Function Remote Receiver with Replaceable Fuses # LC305117 will most likely be located close to the control panel for your leveling system, but it can be located elsewhere and still be wired correctly. The manufacturer does not specify a location. The best way to find it is to follow your trailer battery wires because every RV is different.

expert reply by: Jason S

0

Answer 1

Yes, the Replacement 5-Function Remote Receiver with Replaceable Fuses #LC305117 does work with the Lippert OneControl system.

view full answer...

Answer 2

I spoke to Lippert about the Replacement 5-Function Remote Receiver with Replaceable Fuses part #LC305117. They told me that the receiver must receive a minimum of twelve volts on any of the given inputs in order for it to function correctly. That…

view full answer...

Answer 3

The Replacement 5-Function Remote Receiver with Replaceable Fuses #LC305117 will fit on any motorhome that has the Lippert Linc remote. If you want to add this feature you can use the receiver along with the Replacement New-Style Linc Analog Remote -…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 8

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 9

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 10

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 11

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 12

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Replacement 5-Function Remote Receiver With Fuses

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching