Dimension From End to Center of Hitch Pin Hole on Curt Solid Steel Bar # C49537

Question

Question:

What is the distance from the end of the bar to the center of the hole?

asked by: Dale S

0

Expert Reply:

The Curt Solid Steel, 2" Hitch Bar with Raw Finish - 8" Long # C49537 has a measurement of 2-1/2 inches from the end of the bar to the center of the hitch pin hole. I've attached a video to further assist.

expert reply by: Jason S

0

click to enlarge

Answer 1

Hello Dan, thanks for reaching out. I do have a product I believe will work for you, but the Replacement Extra Long Trailer Tongue for CE Smith Multi-Sport Trailers #CES45FR is 2" wide by 3" tall so this would not fit a 2" hitch. If…

view full answer...

Answer 2

There is a 24 inch long hitch extender that is rated for 6,000 pounds or more but you would have to install a different trailer hitch on your truck. Specifically it will need to be a Tork Lift SuperHitch Original or Magnum. These hitches are…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 6

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Answer 7

Hi David! There are quite a few hitches offered for your 2026 Honda Odyssey, so I definitely understand wanting to know the differences. There are basically three styles available for you and I have them broken out below: Exposed Crosstube: etrailer…

view full answer...

Answer 8

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 9

Both the Roadmaster and Blue Ox tow bars are great options. But if it was my decision to make I would go with the Blue Ox Avail part #BX7420 as we have found that the Blue Ox tow bars are a little easier to connect and disconnect from. Also this tow…

view full answer...

Answer 10

Hey Eric, The hitch extenders that we currently offer for a 2-1/2" receiver tube opening unfortunately max out at 6,000lbs GTW and wouldn't be capable of towing the trailer. You're most likely going to need to upgrade to a TorkLift…

view full answer...

Answer 11

Hey Cindy, thanks for reaching out. We may have an extension that will work for you. It will help to know exactly how long of an extension you are needing as this will be one of the main deciding factors. Let me know how long you need it to be in the…

view full answer...

Answer 12

Hi Brian, great question and I completely understand wanting to be sure everything lines up cleanly before you commit, especially with a newer truck and the SuperHitch in the mix. The TorkLift tie downs part #TL86NR are confirmed to fit your 2026…

view full answer...

Dimension From End to Center of Hitch Pin Hole on Curt Solid Steel Bar # C49537

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching