Replacement Hardware List for B and W Gooseneck Hitch part # BWGNRK1313

Question

Question:

Can you buy just the bolts needed to install this hitch

asked by: Josh

0

Expert Reply:

We don't carry just a hardware kit for the bolts of a B and W gooseneck hitch part # BWGNRK1313. Your best option would be to take the following list of bolts to your local hardware store so that you can piece together everything you'd need. Also this list is in the attached install instructions page link.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Moving a trailer axle from being overslung to underslung really isn't a big ordeal. It's basically just welding on a new spring seat on the other side of the axle and then using the hardware upside down. We sell kits for this. The diameter of…

view full answer...

Answer 2

Shane, sorry to say we don't have a replacement hardware kit by itself for the B&W Turnoverball #BWGNRK1313. The hardware actually does not look like it's offered by B&W themselves, unfortunately. What I did instead is attach a…

view full answer...

Answer 3

While we don't have a replacement hardware kit we can offer you for the #BWGNRK1016 I did attach a picture that shows all of the hardware you'd need that you could source at a local hardware store. I also attached an install video link for…

view full answer...

Answer 4

The B&W Turnoverball Gooseneck Custom Installation Kit #BWGNRM1313 contains the mounting hardware and brackets for the Hitch #BWGNRK1313. It does not contain the Center Section #BWGNRC900 or Safety Chain U-Bolts #BW1900-2-1600. This is the only…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Replacement Hardware List for B and W Gooseneck Hitch part # BWGNRK1313

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching