Longest Available 2 Inch Trailer Hitch Extender

Question

Question:

Is 18 inches the longest extension made to fit in a 2 inch reciever?

asked by: Mark

1

Helpful Expert Reply:

The longest trailer hitch extender we offer is the TorkLift SuperTruss Hitch Extension part # TLE1560 which measures 60". However, the SuperTruss will require you to use a SuperHitch like part # TLC1204. The longest trailer hitch extender we offer for a 2" trailer hitch that does not require the SuperHitch is indeed 18" like part # C45796. Please note that a hitch extender minus the SuperTruss will reduce your tongue weight capacity by 50%.

I have attached a list of all the 2" trailer hitch extenders we offer for you.

expert reply by: Conner L

1

Answer 1

Hello Gerry, thanks for reaching out. The correct weight distribution (WD) hitch will depend on the loaded tongue weight of your travel trailer. Each WD hitch has a range of tongue weights it will work with, and ideally you want your trailers tongue…

view full answer...

Answer 2

Weight distribution/sway control (WD/SC) systems need to be tuned to your trailer tongue weight in order to work properly. A system rated too low for your actual tongue weight (TW) will not have the stiffness needed to shift trailer TW forward to the…

view full answer...

Answer 3

Hi Sam; is there another connection in the vicinity of the one from your picture? The Brandmotion Tailgate Delete Backup Camera #BM22FR is designed to be used without the tailgate. See the attached photo with the connector. It isn't super clear…

view full answer...

Answer 4

The span you refer to on the etrailer Trailer Hitch Receiver Lock for 2" Hitches #e98880 is the usable length of the pin. To properly measure for this, you can measure the outside walls of your hitch at the pin hole. If you measured, and got…

view full answer...

Answer 5

For starters, the TorkLift SuperTruss Hitch Extension will only work if you have a SuperHitch Original, Magnum, or Hero already installed on your tow vehicle. These hitches have a dual receiver tube opening which is what allows them to work with the…

view full answer...

Answer 6

As we do not carry the Atwood jacks, I cannot confirm the fitment without knowing the measurements. However, the bolt holes on the HappiJac Swing Out Extension Brackets #LC182496 will measure 7-1/4" between all the bolt holes, picture included.…

view full answer...

Answer 7

Hello Dale, thanks for reaching out. We do carry Solera awnings which can be used to replace Dometic awnings. I was not able to find any reference for the part number you provided, but it appears to be a 16' awning, correct? If so, we can provide…

view full answer...

Answer 8

There area few differences between the 1,200 and 1,400 pound Equal-I-zer systems. The heads are different and the spring bars are different. If your tongue weight is over 1,200 pound then the 1,200 pound system is not rated high enough. When…

view full answer...

Answer 9

First you are going to want to disassemble one of your hubs to verify if you have the #42 Spindle #TRU37FR. I have found this is the spindle some have found but you will need to determine it is what you have and if not you will need to have a pair of…

view full answer...

Answer 10

We do carry longer ball mounts so that you can use the Ball Mount Bike Racks like the Curt Clamp-On 3 #C18013. For example the Ball Mount part #BM20 has a distance of 13-1/4 inches from the center of the hitch pin hole to the ball hole. If you need a…

view full answer...

Longest Available 2 Inch Trailer Hitch Extender

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching