Replacement Hitch Ball for Curt Pintle Hook Combo Dimensions

Question

Question:

What is the total height of the ball inside the pintle? That is, the height from the flat of the base to the top of the ball. This would tell me what the pintle opening should be when it is in the locked position. Thanks

asked by: Ernest C

0

Expert Reply:

I went down to our warehouse and measured the Replacement Hitch Ball for Curt Pintle Hook Combo # C48820. The height of the ball inside the pintle is 2-1/2 inches (see picture). The overall height of the hitch ball is 5 inches.

expert reply by: Timothy G

0

click to enlarge

Answer 1

You will need to cut a 2-5/16 inch mounting hole for installation of the 2 inch Round Flush Mount Grommet, item #A54GB, and the Sealed, 2 inch Round Trailer Clearance and Side Marker Light, item #MC53RB. The proper wiring pigtail for this light is…

view full answer...

Answer 2

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 3

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

Hey Jonathon thank you so much for all of that additional information! To haul your bikes behind your class C Sprinter motorhome, while flat towing your Mini, I recommend the Hollywood Racks RV Rider Bike Rack item #HLY64FR and the Roadmaster Dual…

view full answer...

Answer 6

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 7

Thanks for letting us help Ben. For a setup like yours, I'd recommend loading the UTV and connecting the trailer with the Pacbrake airbags at their minimum required pressure. From there, you'll want to adjust the B&W Continuum weight…

view full answer...

Answer 8

Hi Ryan; the Weigh Safe Hitch w/ Built-In Scale for 2.5" Hitch #WS56ZR is designed in the US but manufactured in China. The Weigh Safe ball mounts with the built-in scale are pretty unique so we don't have a USA made option with the same…

view full answer...

Answer 9

The appropriate torque spec for any application will vary depending on the construction of the wheel as well as on the stud size. I suggest checking the wheels you're using to see if their manufacturer has a suggested torque rating. Steel trailer…

view full answer...

Answer 10

There sure is K.C.. For a shorter weight distribution shank that fits a 2-1/2" hitch, I recommend the Equal-i-zer item #EQ90-02-4700. This shank measures 12" long x 9-1/2" tall. It provides up to a 3" drop and has a 16,000 lbs…

view full answer...

Answer 11

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 12

Hey Larry, Yes, a high-low adapter may be needed to keep the tow bar level between your Class A motorhome and your 2026 Ford Maverick. With the Roadmaster #RM87NQ base plate and 225/55R19 tires on the Maverick, the tow bar attachment height is about…

view full answer...

Replacement Hitch Ball for Curt Pintle Hook Combo Dimensions

Product Page this Question was Asked From

Continue Researching