Bearing Buddy Recommendation with Outer Diameter of 2-3/8 inch

Question

Question:

Measurements are 23/8 looked up part for trailer An its says it 11/4 in outer and gives me a part number of 4410243. 25580 and lm67048 are the bearing numbers. Its a shorelander srv34b. Looking to purchase 2 bearing buddys and caps. Thanks

asked by: Jody W

0

Expert Reply:

Since you need a Bearing Budddy with an outside diameter of 2-3/8 inches the closest Bearing Buddy we have is the part # BB2328 which has an outer diameter of 2.328 inches. This comes with bras to fit the Bearing Buddies as well.

expert reply by: Jameson C

0

Answer 1

Hey Josh. Your 2021 Alliance 340RL has dual 7,000 lbs axles so the DeeMaxx Disc Brake Kit w/ Actuator item #DE66AR is exactly what you'll need. The rotors have inner bearing item #25580 and outer bearing item #14125A. They work with 15" to…

view full answer...

Answer 2

For your boat trailer I recommend the Bearing Buddy Bearing Protectors - Model 2328 - Chrome Plated (Pair) #BB2328. These are designed to have extra grease and keep water out of your hubs so they can be completely submerged. If you are looking for a…

view full answer...

Answer 3

You would need to measure the inside diameter of the hub opening to determine which cap size is needed. You would want to choose a cap whose outside diameter matches the inside diameter of the hub. Some of the most common sizes are 1.980 inch, 1.986…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

The Demco Hydraulic Trailer Brake Actuator part #DM72VR should be a direct replacement for the Atwood 61101 Brake Actuator that you have now. This newest updated it rated at 7K instead of 6K. This is a bolt on option that mounts on 3" centers.…

view full answer...

Answer 7

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 10

Hey Robert, yes the Kodiak disc brake calipers part #KDBC225DAC that you referenced will replace the Tie Down calipers you have now 46304, they can be used as a left or right hand caliper and does come with ceramic brake pads. If you ever needed…

view full answer...

Answer 11

The #84 spindle is just a common way to identify the spindle dimensions typically used for 3,500 lb axles. So instead of listing out the parts, people can just say they have #84 spindles and it's easier to know what fits it. The CE Smith Trailer…

view full answer...

Answer 12

You can use leaf springs that are rated higher than the axle without any issues as long as they measure the correct measurement for your trailer. For example the 6-leaf double eye spring for 7,000 lb axles part #e64SR measures 24-7/8" eye to…

view full answer...

Bearing Buddy Recommendation with Outer Diameter of 2-3/8 inch

Product Page this Question was Asked From

Continue Researching