A-Frame Trailer Jack Operation and Tongue Weight
Updated 06/01/2018 | Published 05/31/2018 >
Question:
Hi E-Trailer Staff, I believe I have this make of top handle hand crank trailer jack. It does not have any logos whatsoever on the jack but the A-Frame has an Atwood part #. The trailer is currently in the driveway and the foot of the jack is extended but not fully and sitting on several levels. The problem is when I turn the handle counter clockwise to raise the foot of the jack the tongue starts to lower but the foot does not retract/raise. I lifted the trailer with a 2 1/2 ton jack just alittle bit off the levelers-then I can retract the foot of the trailer jack. What might be the problem here? Thank you all so much-your help is always appreciated.
asked by: Carolyn B
Expert Reply:
From what you told me it sounds like the foot on your trailer jack, like part # TJA-2001-B, doesn't leave the ground until you have the tongue weight of the trailer supported. Since the purpose of an A-Frame trailer jack is to support the tongue weight of the trailer if you don't have anything else supporting the tongue weight of your trailer it will naturally go down as the foot retracts into the jack.
When your trailer is parked and uncoupled it is always best to leave the foot of your jack down. The only time you should be retracting that jack is when the trailer is coupled and the hitch ball/trailer hitch of the tow vehicle is taking on the tongue weight of the trailer.
Let me know if you have any other questions.
Product Page this Question was Asked From
Round A-Frame Trailer Jack - Topwind - 14-1/4" Lift - 2,000 lbs - Black
- Trailer Jack
- Enclosed Trailer
- Utility Trailer
- A-Frame Jacks
- Topwind Jack
- 1001 - 2000 lbs
- Manual Jack
- 14 Inch Lift
- Bolt-On
- Weld-On
- No Wheel or Foot
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: trailer leaf springs
- Search Results: trailer jack plate
- Search Results: trailer axles
- Video: Complete Breakdown of the Timbren Axle-Less Trailer Suspension w/ Idler Hubs
- Shop: 4-Leaf Double-Eye Spring for 3,500-lb Trailer Axles - 27" Long
- Shop: Round A-Frame Trailer Jack - Topwind - 14-1/4" Lift - 2,000 lbs - Black
- Shop: Footplate for 2,000-lb and 5,000-lb Round, A-Frame Jacks
- Q&A: Replacement Axle for 1968 Shasta Camper
- Q&A: Light To Replace Older Reflecto Light 110-150 On Travel Trailer
- Q&A: How To Determine the Correct Boat Trailer Jack Weight Capacity
- Q&A: Recommendation for an A-Frame Jack with a Lower Retracted Height Than 8 Inches
- Q&A: Recommendations For Allowing Trailer Jack To Be Able To Swing Up Without Hitting Ground
- Shop: Timken Bearing Kit, L44643 Inner/Outer Bearings, L44610 Inner/Outer Races, 204507 Seal
- Shop: 3-Leaf Double-Eye Spring for 4,000-lb Trailer Axles - 25-1/4" Long
- Shop: Shackle Bolt with Locknut for Double-Eye Springs - 3" Long
- Shop: etrailer Drop Leg for V-Groove Trailer Jacks - 13-1/4" Tall - 6" Diameter Footplate
- Q&A: Difference Between 3 and 4 Leaf Spring Stack for 3,500 Pound Axle
- Q&A: Ideas to Prevent Rodents from Eating Trailer Wiring
- Shop: Trailer Hitch
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Shop: Trailer Wiring
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Search Results: trailer tires and wheels
- Video: Firestone Ride-Rite Air Bags with Easy Mount Compressor Feature Breakdown
- Search Results: trailer wiring
- Article: Wiring Trailer Lights with a 7-Way Plug (It's Easier Than You Think)
- Shop: Suspension Enhancement
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Search Results: trailer jack


