How Much Does the Ram Scissor Stabilizer Jack # TJSC-24 Weigh

Question

Question:

What is the actual weight of the scissor jack itself? I am looking for the lightest one available as i am not worried about weight capacity because my tent topped utility trailer only weighs about 1,000 pounds loaded.

asked by: Garrett P

0

Expert Reply:

The Ram Scissor Stabilizer Jack # TJSC-24 has a shipping weight of 12 lbs. When you take away a few lbs for the shipping materials that leaves you with about 10 lbs just for the jack itself.

expert reply by: Jon G

0

Answer 1

It sounds like your springs are more than likely maxed out if they have a 1750 lbs capacity and your trailer is 3400 lbs loaded. Getting in the trailer and moving around is adding extra weight to the springs as well. If the leaf springs sit below the…

view full answer...

Answer 2

The stabilizer jacks aren't trailer specific, but the mounting hole spacing is pretty standard across the board. I'd recommend removing the damaged jack and comparing the mounting plate hole spacing to what's shown in the provided photos.…

view full answer...

Answer 3

The #TJSC-24 scissor style stabilizing jack isn't an RV specific product, if it's 2500 lb capacity and 18-3/4 inch lift and the pictured mounting bolt pattern is compatible with your Rockwood Mini-Lite, it'll work perfectly for you.…

view full answer...

Answer 4

Hey Kristin; the Heng 12V JRP1007B Range Hood Bulb is a wedge type bulb. Based on the length it looks like the bulb size is a T-15 so you can use the #DI39VR you were looking at as a replacement. If you need anything else feel free to reach out in…

view full answer...

Answer 5

C921 and 921 bulbs are the same fit so what you have should fit. The difference is the C921 is supposed to be just a little brighter. If you can't get your 921 bulb to fit you might check to make sure your old bulb is a 921.

view full answer...

Answer 6

The 906/921 LED Bulbs #DI38VR will work great for the overhead lights in your 2008 Itasca Navion motorhome. There's no need to replace the entire light unless you wanted to. Replacing the bulb is much easier and more cost effective. LEDs use less…

view full answer...

Answer 7

The Replacement Lamp Socket for Ventline RV Range Hood #BCB0267-02 that you referenced is designed to be used with a 12 volt power source. For a switch to go with it you'd want the part #BL0108-00-R and then the style of bulb it uses is a 921…

view full answer...

Answer 8

The R-Pod 189 usually comes fitted with four corner-mounted scissor jacks that bolt to the frame. We have a number of such bolt-on stabilizer jacks that are shown on the linked page. Many of these are sold as pairs but we also have single jacks too,…

view full answer...

Answer 9

Yes, the 921 bulb #VA0415-00 will work well for you. The 912 and 921 bulbs are interchangeable as they have the same T-5 wedge base. The 921 has a wattage of 16.8 and draws 1.4 amps. The 912 is 12 watts and draws 1 amp. So the 921 should burn…

view full answer...

Answer 10

I spoke with the manufacturer and the specs for the screw on the Scissor Stabilizer Jack - 18-3/4" Travel - 2,500 lbs - Qty 1 #TJSC-24 are as follows: TPI: 8 threads per inch Diameter: 5/8" Material: 20Cr Steel

view full answer...

Answer 11

The Ram Scissor Stabilizer Jack #TJSC-24 that you referenced weighs 12 lbs.

view full answer...

Answer 12

In regards to the Scissor Stabilizer Jack part #TJSC-24, the slot is not designed to support the frame. I must recommend you attach the two ears to the bottom of the frame as you can see in the attached video. I have also attached for you some…

view full answer...

How Much Does the Ram Scissor Stabilizer Jack # TJSC-24 Weigh

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching