Disconnecting Lippert Powered Stabilizer Jack Power to Operate the Jack Manually

Question

Question:

It says to “disconnect the motor from the battery” before manual operation. Can this be done just by pulling my main battery bypass switch or does it need to be disconnected closer to the motor?

asked by: Gretchen

0

Expert Reply:

Basically as long as power is removed before you manually operate the jack it doesn't really matter which method you follow. The issue is that should the motor start to operate off of electrical power for some reason the manual crank would start to spin and that can cause injury. So that is what you want to avoid and the only way to ensure that is to make sure the power source is removed from the equation.

expert reply by: Michael H

0

Answer 1

The outer diameter of the tire size you have of 205/75R14 is 26.3 inches so a cover like the #290-3954 would be your best option.

view full answer...

Answer 2

I do have an option for you but there aren't any slide-on, clip-on, or slip-on towing mirrors for a 2017 Ford Expedition. The only options are the ones which use straps but if you're looking for an upgrade the best ones we have are the…

view full answer...

Answer 3

We have really great universal style tow mirrors that fit your 2017 Ford Expedition like the K-Source #KS3990 but we don't have any slip on style confirmed as a fit for your vehicle. We had the chance to install the K-Source mirrors and we found…

view full answer...

Answer 4

Hey Dale! I recommend the NOCO Genius Smart Battery Charger #329-GENIUS5 to keep your batteries maintained in storage. This will plug into that AC outlet and works with 12V batteries up to 120Ah. Since it is a smart charger it will keep them topped…

view full answer...

Answer 5

It looks like your batteries are wired in parallel so the positive cable of the NOCO Genius Smart Battery Charger #329-GENIUS10 can be ran to the positive post on one battery and the negative cable from the charger can be ran to the negative post on…

view full answer...

Answer 6

Yes there's a manual crank for the Lippert stabilizer jacks part #LC298707 with the part #LC119226.

view full answer...

Answer 7

The Swagman Around the Spare Deluxe 2 Bike Rack for RV Bumpers #S80501 with two standard bikes is not too much weight for your Flagstaff Ultra Light 4 inch bumper. The rack weighs about 20 lbs and can carry two bikes up to 35 lbs each. I assume you…

view full answer...

Answer 8

The inner shroud of the vent is for looks only so it's very concerning that you're getting water through the cracks in it from overtightening the mounting screws. This would be an indication that you have a leak originating somewhere up on…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Disconnecting Lippert Powered Stabilizer Jack Power to Operate the Jack Manually

Continue Researching