Will There Be Movement in Stake Pocket When Stake Pocket Tie-Down Anchors # PK-SPTD are Installed
Published 04/05/2018
Question:
Even using the bolts to secure the Tie downs vertically, is it OK that they would slide from side to side, given the width difference between the pockets and the tie downs?
asked by: Nick C
Expert Reply:
With the Stake Pocket Tie-Down Anchors # PK-SPTD there are two ways this can be installed. The more permanent method which requires you to use the nuts on the pin that runs through it which holds it tight and prevents movement. Or using the cotter pin which allows a bit more movement but also the ability to remove when not needed.
If you used the nuts to tighten the anchors down you'd get rid of the movement.
Product Page this Question was Asked From
Stake Pocket Tie-Down Anchors - Black Powder Coat - 2-3/4" D-Ring - 4,000 lbs - Qty 2
- Trailer Tie Down Anchors
- D-Rings
- Stake Pocket
- Powder Coated Steel
- 4000 lbs
- Drop-In
- Folding
- PackEm
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: stake pocket d rings
- Shop: etrailer Axle Straps w/ D-Rings - 2" Wide x 24" Long - 3,333 lbs - Qty 2
- Shop: Stake Pocket Tie-Down Anchors - Black Powder Coat - 2-3/4" D-Ring - 4,000 lbs - Qty 2
- Shop: etrailer Ratchet Strap w/ Snap Hooks - 2" x 10' - 3,333 lbs - Qty 1
- Shop: Stake Pocket Tie-Down Anchor - D-Ring - Black Powder Coat - 4,000 lbs
- Q&A: Where is Stake Pocket Tie-Down Anchor WFSPDR Made
- Shop: BulletProof Hitches 2-Ball Mount for 2" Hitch - 8-1/4" Drop, 8-3/4" Rise - 14,000 lbs
- Video: An In-Depth Look at the Brophy Stake Pocket Tie Down Anchor
- Video: An In-Depth Look at the Stake Pocket Tie-Down Anchors
- Video: Breaking Down the Stake Pocket Tie-Down Anchor
- Video: A Closer Look at the Stake Pocket Tie-Down Anchor
- Video: A Closer Look at the etrailer Ratchet Strap with Snap Hooks
- Shop: Stake Pocket Tie-Down Anchor - Black Powder Coat - 2-1/4" D-Ring - 4,000 lbs
- Shop: Stake Pocket Tie-Down Anchor - Black Powder Coat - 2" D-Ring - 1,600 lbs
- Search Results: stake pocket d~rings
- Search Results: axle straps
- Search Results: ratchet straps
- Search Results: stake pockets tie down anchors
- Search Results: trailer hitch ball mount
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Hitch
- Search Results: trailer hitch
- Article: Trailer Wiring Diagrams
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Video: How to Choose a Trailer Brake Controller
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Q&A: What is the Difference Between a 4-Way and 7-Way Trailer Connector
- Article: How to Measure for Trailer Hitch Drop
- Video: Curt T-Connector Vehicle Wiring Harness Review C56040
- Q&A: What Is An OEM Prep Package And How Do I Know If I Have It
on Trailer Tie Down Anchors
Nick C.
4/5/2018
Even using the bolts to secure the Tie downs vertically, is it OK that they would slide from side to side, given the width difference between the pockets and the tie downs?