2017 Lexus GX 460 Timbren Rear Suspension Kit Recommendation

Question

Question:

Hello, I have a 2017 Lexus GX460 with towing capacity of 6500 lb. My vehicle is equipped with a factory tow package that is designed to be used with a weight distribution system. I don't need a towing hitch. My question was if the Timbren Rear Suspension Enhancement System will fit my vehicle.

asked by: Stefan H

0

Expert Reply:

Yes, the Timbren Rear Suspension kit part # TTORSEQ is a confirmed fit for your 2017 Lexus GX460 and would work great for you.

expert reply by: Jameson C

0

Answer 1

Timbren rear axle jounce spring kits, like #TTORSEQ that fits your 2005 Lexus GX 470, are normally not engaged with the axle with the vehicle unloaded, meaning not full of passengers and/or cargo and not loaded by trailer tongue weight. If you were…

view full answer...

Answer 2

We went out to our warehouse and measured an overall height with the mounting bracket of 5 inches for the Timbren Rear Suspension Enhancement System #TTORSEQ. Timbren recommends having a 1/2 inch to 1-1/2 inches between the spring and the axle when…

view full answer...

Answer 3

I have a solution for your towing needs, however, there are currently no air suspension options for your 2017 Lexus GX460. If you are wanting to extend the life of your vehicle's suspension and reduce body roll, I would look into rear suspension…

view full answer...

Answer 4

Using Timbren helper springs on your 2015 Lexus GX 460 will improve the ride quality on those rough roads. It may not completely eliminate everything but it will be a vast improvement. What is likely happening is the weight of the trailer is pulling…

view full answer...

Answer 5

The 6,000 pound capacity of the Timbren springs #TTORSEQ is the capacity of the system or, in other words, the amount of weight pushing straight down on them that they can handle. So if you put 2,000 pounds of stuff over the rear axle of your 2014…

view full answer...

Answer 6

Hey Bob, Since your 2019 Lexus GX 460 is lifted in the back some, the Air Lift 1000 Air Helper Springs #AL94VJ aren't able to reach properly which is why you're not getting the effect you're wanting. You can add multiple of the 1"…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

Since the pin weight of your camper is 2.1k, I recommend going with the LoadLifter 5000 opposed to the 7500. While technically there is not reason you couldn't use the 7500 kit, it really is not necessary for a camper like yours. Generally the…

view full answer...

Answer 10

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 11

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Answer 12

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

2017 Lexus GX 460 Timbren Rear Suspension Kit Recommendation

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching