Replacement Hardware Kit for Draw-Tite Trailer Hitch # 24704

Question

Question:

Do you sell only the bolts to mount the reciever hitch to the frame? If do how cna I order a set.

asked by: Wayne N

0

Expert Reply:

We do offer a replacement hardware kit for trailer hitches. What you will need is part # RHK. Under the box that says Shipping Special, type in the hitch number, in this case 24704. The under that, choose the hitch manufacturer from the pull down menu, Draw-Tite for hitch # 24704. Click Add to Cart, and that is all there is to it.

expert reply by: Michael H

0

Answer 1

Hey Dave, Yes, Dometic lists the Replacement Circuit Board for Dometic Atwood Water Heaters #DMC89FR (91365) as a replacement for the WH-6GEA water heater models.

view full answer...

Answer 2

Hey Connie, unfortunately we do not offer any BAL products or replacements for their systems. The best we can do over here is offer a full replacement system with something like the Lippert Ground Control 3.0 Electric 5th Wheel RV Leveling System w…

view full answer...

Answer 3

Thank you for providing that information. What you need is the Replacement Motor for Kwikee Electric RV Steps #LC379147. This will replace the motor you have now and get your steps up and running again.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 7

You are able to order replacement hardware for the Curt Trailer Hitch Receiver #C13315 for your 2022 Mazda CX-5. The Replacement Hardware Kit #RHK will allow you to type in your hitch number(C13315) and order all the hardware needed to install your…

view full answer...

Answer 8

We have just what you need. If you type RHK in the search box on our website it will take you to the replacement hardware kit product page. You will then simply type the number of the hitch you need hardware for in the box that is labeled Hitch Item…

view full answer...

Answer 9

Hey Kelvin, welcome back. To flat tow a 2026 Ford Maverick with your Demco Commander II Tow Bar item #DM9511012, I recommend the following parts: Baseplate Kit - Demco Tabless Base Plate Kit item #DM38CV Wiring Harness - Roadmaster Diode 7-Wire to…

view full answer...

Answer 10

Hello Sean, Thanks for writing in. For a replacement hardware kit you will want to order the Replacement Hardware Kit for Trailer Hitches #RHK. Above "ADD TO CART" you will need to put "Curt C15410" so the warehouse knows what…

view full answer...

Answer 11

Yes, we do Jay! It is the Replacement Hardware Kit for Trailer Hitches item #RHK. This will have all of the hardware you need to install the Curt Hitch item #C14017, you were looking at. You will want to go to the item #RHK product page and on the…

view full answer...

Answer 12

The bolts included with the Draw-Tite Class III #75471 Hitch are Class 10.9. They're 10mm in diameter, 30mm long and have a 1.25 thread pitch. If you're needing replacement installation hardware, we can supply a replacement hardware kit for…

view full answer...

Replacement Hardware Kit for Draw-Tite Trailer Hitch # 24704

Product Page this Question was Asked From

Continue Researching