Do You Sell Replacement Installation Hardware for Curt Hitches?

Question

Question:

Do you sell installation hardware?

asked by: Jay B

0

Expert Reply:

Yes, we do Jay! It is the Replacement Hardware Kit for Trailer Hitches item # RHK. This will have all of the hardware you need to install the Curt Hitch item # C14017, you were looking at. You will want to go to the item # RHK product page and on the right hand side where it says Hitch Item Number you'll want to insert C14017.

I have linked an installation video along with the instructions so you can see how to get the Curt item # C14017 installed on your 2015 Ford F-150.

Is the Curt item # C14017 the hitch you're needing hardware for?

expert reply by: Jerred H

0

RHK
(click to enlarge)

Jarred H.

6/21/2025

Yes. I'm needing the installation hardware for C14017.

Jerred H.

6/21/2025

@JarredH How did you end up with a hitch and no hardware?

Jarred H.

6/21/2025

@JerredH The hitch was hitch was shipped with just shrink wrapped and not in a box. The hardware bag was ripped. I have about half of the hardware that im supposed to.

Jerred H.

6/21/2025

@JarredH Oh that's disappointing. The reason I asked is some vendors ship their hardware stuffed inside the receiver and people don't like to look there.

See All (4) Replies to Jarred H. ∨

Answer 1

We do have installation hardware for it but that is an older hitch which we no longer carry. You will need the Replacement Hardware Kit item #RHK. This kit will include all the necessary bolts with proper grades, spacers, nuts, and the fish wire tool…

view full answer...

Answer 2

What you need is the part #RHK. This hardware kit comes with everything needed to install the Curt hitch part #C11681. On it's product page you would need to enter the part number of the hitch as well as select the brand Curt from the drop down…

view full answer...

Answer 3

Hey Wayne! The answer to your question is maybe. As you know, the Curt #C14017 is designed for the F-150 without the factory hitch. Typically this is because the factory hitch is integrated with the bumper and removing it to replace it with the…

view full answer...

Answer 4

The Draw-Tite 41954 Class V hitch which we offer as part #DT35MR is designed for 2015 - 2022 Ford F-150 models that aren't equipped with a factory hitch. I've made up a diagram showing the dimensions and hole spacing for you.

view full answer...

Answer 5

Yes. This seal will adhere to a spray-on bed liner and although the #PARTS-326A0005 can be used, I checked with Bak and they recommend using the thicker 3/8" seal #PARTS-326A0004 as the seal to use on spray-on bed liners for the BAK Flip series…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 12

Hey Ricardo! Yes, the Curt Trailer Hitch Receiver #C82RJ is the hitch Curt is working on for the new 2027 Telluride. This is a pre-order since Curt hasn't finished the design. It does not include wiring. The wiring harness for the 2027 is also up…

view full answer...

Do You Sell Replacement Installation Hardware for Curt Hitches?

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching