Adapter Fittings, Tubing, and Clamps for Atwood Water Heater

Question

Question:

I just installed the Atwood water heater I purchased from you but realize I need new 90 degree elbows as I have leaks coming from the old female ones. Will these male fittings work and can I buy extra tubing and clamps from you as well?

asked by: Darrin V

0

Expert Reply:

For your Atwood GC6AA-8 RV Water Heater you can use the Valterra 90-Degree Male Adapter # RF882 fittings you mentioned. You will want to use sealant as well.

For matching tubing, I recommend the Valterra Vinyl Tubing # W01-1400PB and hose clamps # H03-0020.

expert reply by: Jason S

0

click to enlarge

Answer 1

Hey Scott, thanks for reaching out. Generally speaking, installing a soft start will not void your Ac units warranty. Your AC warranty is protected by the by the federal Magnuson–Moss Warranty Act. This act states, in part, that unless the…

view full answer...

Answer 2

In the attached diagram the A measurement is actually the distance from the center of the spring hangers for a single axle trailer. The spring eye to spring eye measurement for your leaf springs will be slightly different. The B measurement that you…

view full answer...

Answer 3

The Replacement 4.3" Monitor #FR77FR is specific to only the Furrion Vision S Camera #FCN48TASF. If you have one of the older Vision 1 or 2 cameras you will not be able to pair with the new monitor. This sounds like what is causing you to have…

view full answer...

Answer 4

I've attached the fresh water fittings page so you can get the connections you need. I unfortunately can't give you parts without knowing the hose measurements and the tank measurements. For instance it looks like you will need the Valterra…

view full answer...

Answer 5

The Valterra RV Water Tank #R8042 has 6 ports (3 on each side) to allow for different ways to mount your tank. One hole is already cut out with a red plug but the rest would require you to drilling out the hole before attaching your plumbing to the…

view full answer...

Answer 6

One of the 3/8 inch ports is open on the Valterra RV Water Tank #R8030 and is plugged by the red cap like you see in the accompanying photo; this is where the tank would be filled. You would not want to modify the opening to fill up the tank, instead…

view full answer...

Answer 7

You can use the RV Propane Gas Detector #RS64FR (white) or #RS44FR (black) to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 8

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 11

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Adapter Fittings, Tubing, and Clamps for Atwood Water Heater

Products Featured in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching