How Much Does the Curt Forged Ball Mount for 2-1/2" Hitches # C45456 Weigh

Question

Question:

How heavy is the Curt ball mount C45456

asked by: Bob

0

Expert Reply:

The Curt Forged Ball Mount for 2-1/2" Hitches # C45456 has a shipping weight of 16 lbs. If you take away a few pounds for the shipping materials that leaves you with about 13 lbs - 14 lbs for the ball mount itself.

expert reply by: Jon G

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The main difference between the Curt Trailer Hitch Receiver part #C13416 and the EcoHitch Hidden Trailer Hitch Receiver part #EH97FR is that the EcoHitch has a completely hidden cross tube whereas the Curt cross tube will be visible from the rear of…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Hey Chris, in the instructions for the B and W Turnoverball gooseneck hitch part #BW73FR that you referenced it says that the inner brackets are not needed if the truck has the inner brackets for the OEM hitch already welded to the truck frame. In…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Hey Travis, welcome back! You're friend makes a good point the only way to lock the B&W Companion OEM 5th Wheel Hitch item #BWRVK3305 is to use a padlock like item #Master Lock 1-9/16" Wide Solid Brass Body Padlock item #ML140DLH. The…

view full answer...

Answer 10

Hi Doug! If you were just needing a weight distribution system for the sway control, I would have said the Andersen Weight Distribution Hitch w Sway Control - 6" Drop/Rise - 14K GTW, 1.4K TW #AN53VR could be a good option. However, I have tried…

view full answer...

Answer 11

Curt recommends the use of 250 ft/lbs of torque when tightening the nuts of their hitch balls with a 1 inch diameter shank like the part #C40034 that you referenced. The general rule is for a 3/4" shank tighten to 150 ft/lbs For a 1" shank…

view full answer...

Answer 12

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

How Much Does the Curt Forged Ball Mount for 2-1/2" Hitches # C45456 Weigh

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching