When Should Weight Distribution System be Replaced
Updated 01/03/2018 | Published 01/02/2018 >
Question:
I have a weight dist. system that is 10 years old. is thee a point when it should be repaced?
asked by: Ken H
Expert Reply:
There is not a specific lifespan for a weight distribution system. If maintained and the system is properly rated for your towing setup, it can potentially last for a long time. When determining if it should be replaced, you will just want to take note of its various components, checking for excessive wear, rust or corrosion. Also keep in mind that individual parts can usually be replaced if needed without replacing the entire weight distribution system.
If you find that you do need to replace the system, or a few of its components, please let me know what manufacturer/model you currently have, or your system's total tongue weight (tongue weight of fully loaded trailer plus weight of any added cargo from behind the rear axle of tow vehicle), and I will be happy to recommend a new system or replacement parts for your existing unit.
I have also attached a couple articles on weight distribution that you might find helpful.
Product Page this Question was Asked From
Curt Welded Weight Distribution Shank 7" - 10 Hole Adjustment
- Accessories and Parts
- Weight Distribution Hitch
- Shanks
- 1400 lbs TW
- Fits 2 Inch Hitch
- Round - 8 Inch Drop
- Trunnion - 8 Inch Drop
- Round - 12 Inch Rise
- Trunnion - 11 Inch Rise
- CURT
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Search Results: weigh safe weight distribution hitch
- Search Results: tire pressure monitor
- Search Results: 7 way plug
- Search Results: hitch rack
- Search Results: tire pressure gauge
- Search Results: hitch basket
- Search Results: furrion back up camera
- Shop: Trailer Wiring
- Shop: Trailer Hitch
- Shop: Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 4-Pole Flat Trailer Connector
- Shop: Curt Trailer Hitch Receiver - Custom Fit - Class IV - 2"
- Shop: Weigh Safe True Tow Weight Distribution Hitch - 2.5" Shank - 8" Drop - 18.5K GTW, 1.8K TW
- Video: How to Set Up Your Curt Trailer Hitch Receiver on a 2007 GMC Sierra Classic
- Shop: Weigh Safe True Tow Weight Distribution Hitch - 2" Shank - 8" Drop - 22K GTW, 2.2K TW
- Shop: Weigh Safe True Tow Weight Distribution Hitch - 2" Shank - 6" Drop - 8.5K GTW, 850 lbs TW
- Shop: Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires
- Shop: 17x46 Curt Cargo Carrier for 1-1/4" and 2" Hitches - Steel - 500 lbs
- Q&A: Looking For A Replacement Scissor Jack For My Forest River Surveyor
- Shop: Towing Mirrors
- Shop: Nerf Bars - Running Boards
- Q&A: Is it Possible to Use Too High Rated of a Weight Distribution System
- Q&A: Comparing B&W Continuum And Reese Strait-Line Weight Distribution Systems
- Q&A: Can You Reverse With the Equal-i-zer Weight Distribution System
- Q&A: Can You Back Up with a Blue Ox Weight Distribution System
- Q&A: Installation Tools Needed for Blue Ox SwayPro Weight Distribution System Part # BXW1001
- Q&A: How Low Does The B&W Continuum Weight Distribution System Hang Below The Trailer?
- Shop: Suspension Enhancement
- Video: Review of Equal-i-zer Weight Distribution Hitch Head - EQ90-02-1000
- Video: Ultimate Overview of the Removable Mounting Plate for 1st Gen MORryde StepAbove RV Steps
- Video: Replacement Spring Bars for Equal-i-zer Weight Distribution Systems Feature Review



