Does Installing Westin HDX Grille Guard on Truck Allow Headlight Bulb Replacement

Question

Question:

Can you still change headlight bulb without having to remove gaurd

asked by: Sean

0

Expert Reply:

When you change the headlights of a truck like what the Westin HDX Grille Guard # 57-3550 fits you actually access the bulb from behind the light under the hood so the grille guard would not interfere with that at all.

You'd have to pop the hood and reach down from behind the housing.

expert reply by: Jameson C

0

click to enlarge

Answer 1

Hi Phil! The main difference between the etrailer Easy Grease Trailer Hub and Drum Assembly #AKHD-865-7-2-EZ-K and the Dexter Trailer Hub and Drum Assembly #42866UC3-EZ is where they are made. Ours are made over seas and Dexter hubs are made here in…

view full answer...

Answer 2

The Westin HDX Grille Guard with Punch Plate #57-3550 (Polished Stainless Steel) or #57-3555 (Black Powder Coated Steel) that fits Ram trucks such as a 2019 Ram 2500 or 3500 will not have enough enough room for you to remove the headlight housing. As…

view full answer...

Answer 3

The tow hooks will remain on your 2016 Ram 2500 when installing Westin HDX grille guard #57-3550. I have included a picture that shows the guard installed and you can see the tow hooks still in place.

view full answer...

Answer 4

Assuming you have the Westin HDX #57-3550 or #57-3555 Grille Guard, you'll need the #57-355PK replacement hardware kit. I looked up the vehicle fits, and the 2018 Ram 3500 and the 2014 2500 use the same HDX Grille Guards. Keep in mind that not…

view full answer...

Answer 5

I checked with Westin and the Westin HDX Grille Guard #57-3550 is a fit for your 2016 Ram 3500 but it would interfere with the front parking sensors. Due to the nature of the parking sensors there isn't going to be a way to install a guard and…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 11

Hey Andrew! Yes, Furrion does have a Chill Cube model with a heat pump. This was actually just released for aftermarket sale. You will need a complete system to make the switch, new R32 units aren't backwards compatible with old R410A systems.…

view full answer...

Answer 12

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Does Installing Westin HDX Grille Guard on Truck Allow Headlight Bulb Replacement

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching