7-Way Recommendation for Attaching to Port in Rear Bumper of 2011 Chevy Silverado

Question

Question:

Can this be mounted next to the license plate in the bumper as a factory replacement on a 2001 Silverado 1500?

asked by: William K

0

Expert Reply:

We have the style of 7-way that would fit the bumper port you have on your 2011 Chevy Silverado but it does not have a 4-way built into it. You'd want the part # PK11916 for a 7-way that fits directly.

You could also install the part # 118384 to give you a separate 4-way as well though.

expert reply by: Jameson C

0

Answer 1

It depends on what function the black wire carries. If you use a circuit tester like part #PTW2992 you can determine what function it carries and then use the attached photo to locate which pin it installs to for the Hopkins Endurance Multi-Tow 7-,…

view full answer...

Answer 2

The etrailer Class III 2 Inch Hitch, part #e45KR, is a confirmed fit for your 2010 Volvo XC90. The Hopkins Endurance Multi-Tow 7-, 5- and 4-Way Flat Trailer Connector, part #HM48470, has a mounting bracket that can be bolted to your hitch. You can…

view full answer...

Answer 3

We have what you need. To start the etrailer Trailer Hitch Receiver part #e63TR is a great choice designed specifically for trucks without the factory hitch. For wiring the Curt T-Connector Vehicle Wiring Harness with 7-Way Trailer Connector part…

view full answer...

Answer 4

You are going to need the 7-Way Trailer Plug Extension #C86DR to go with the Hopkins Endurance Quick-Install 7-Way Trailer Connector #HM55FR on your 2022 Ford F-550 cab and chassis. The included pigtail with the Hopkins is only 1' so the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 9

Yes, it will work. You'll just need to cut the Lance 6-pin connector out and rewire it into the etrailer Trailer Wiring 7-Way Upgrade Kit w/ Junction Box and RV Style Connector item #e99011. Here are the individual functions of that Lance 6-pin:…

view full answer...

Answer 10

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 11

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 12

Hi Paul, you’re definitely on the right track here, and I can help you narrow this down with confidence. With your tandem 3,500 lb Dexter axles and 33 inch spacing, both the Dexter EZ Flex part #K71-652-00 and the Lippert Road Armor part #LC53CK are…

view full answer...

7-Way Recommendation for Attaching to Port in Rear Bumper of 2011 Chevy Silverado

Products Featured in This Question

Continue Researching