Recommended Brake Controller for 2012 Toyota Tundra Crewmax 4x4

Question

Question:

Can you suggest a brake controller. I have a 2012 Toyota Tundra Crewmax 4x4 with towing package. I need to be able to control 2 axles 4 brakes. Dont need anyything fancy. Just something reliable. Thank you

asked by: Kyle R

0

Expert Reply:

For a brake controller, I usually recommend the Tekonsha Prodigy P3 # 90195 because it is a great controller that is easy to use with its LCD display. Because you don't need anything fancy, I recommend a similar unit in the Primus IQ # TK90160 which will have many of the same functions in a more traditional format.

Either one is a proportional brake controller allow the trailer brakes to be applied at the same time and with the same pressure as you hit the brake pedal in your Tundra. It will work with the 2 axles and 4 brakes without issue and give you diagnostics to maintain proper function. I've attached some videos to assist.

Since you already have the tow package, I recommend the custom adapter # 3040-P. This will allow you to simply plug the controller into your dash wiring. The harness is located underneath the dash, to the left of the steering column, taped to another harness near the emergency brake pedal.

expert reply by: Jason S

0

Answer 1

If your 2011 Tundra has the factory tow package, which includes the factory installed 7-way trailer connector on the rear bumper, it will be equipped with the tow package plug under the dash, as shown in the photo I've edited for you. Some models…

view full answer...

Answer 2

Hello Tom, I really wish I could give you a part number for the Tekonsha Prodigy P3, but Tekonsha was owned by First Brands and they filed for bankruptcy. At this time no one has purchased the brand, so the P3 is not available right now. I was…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

According to Blue Ox, it'll take an experienced installer about 4 to 5 hours to complete the installation of their #BX1128 Base Plate Kit on a 2016 Jeep Grand Cherokee. The install isn't what I'd call super-difficult, but the installation…

view full answer...

Answer 6

It sounds like you are speaking of the wires for the brake magnets. If this is correct, you will need to connect one of the wires to the brake controller output wire on your trailer connector and the other wire will need to be grounded to a clean…

view full answer...

Answer 7

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 8

Sure, I can help with that. I can see why the fitment notes are confusing. For a 2012 Toyota Tundra with the factory tow package and factory 7 way connector, you'll want a brake controller that plugs into the factory brake controller port under…

view full answer...

Answer 9

That's a very good question, we tend to be extra cautious and say to use 10 gauge wire because that would be more than enough. When you get into longer trailers that will end up using a lot of wire the heavier gauge wire becomes more necessary.…

view full answer...

Answer 10

Hey Dale, thanks for reaching out. For your 2010 Toyota Tundra with the factory tow package, a proportional controller is definitely the way to go for smooth braking on a 2-axle trailer, and a really clean option is the Redarc Tow-Pro Liberty…

view full answer...

Answer 11

Hey Connor, since your 2007 Toyota Tundra comes with a factory 7-way the correct kit to install the Redarc Tow Pro Liberty would be the part #RED82CR which comes with the correct harness that plugs in under the dash of your truck. What are you…

view full answer...

Answer 12

To install a Redarc Tow Pro Liberty in your 2023 Toyota Tacoma Sport you will need the following parts: Redarc Tow-Pro Liberty Brake Controller item #RED24FR Plug-and-Play Wiring Harness for Redarc Tow-Pro Trailer Brake Controllers item #RED99FR…

view full answer...

Recommended Brake Controller for 2012 Toyota Tundra Crewmax 4x4

Featured Help Information

Miscellaneous Media

Continue Researching